ASIC design services can help industrial technology teams address specialist tasks that fall outside their in-house capabilities, from physical implementation to test insertion and technology selection. For companies developing custom silicon for automation equipment, sensing, control or other embedded applications, the value is not limited to completing a design task: the right support can connect stages of the ASIC lifecycle while allowing the internal team to retain the work it is best equipped to manage.
Service models can be flexible. A project may need help with one part of the flow, such as analog design or implementation, or broader support that begins with a specification and continues through chip production. Understanding the available entry points and technical scope helps teams define a practical division of responsibility.
ASIC design services can fill specific capability gaps
Custom chip development brings together disciplines that require different expertise and tools. A team may have RTL designers, for example, but lack the resources to carry out physical design in an advanced process technology. Another project may need support with analog circuitry, standard-cell libraries, or design-for-test planning. Specialist services can complement the customer’s team rather than replace it.
Support can begin at different stages, including the specification, RTL code, a netlist, placed gates or a GDSII layout. Starting from a specification can include help developing the requirements; starting later in the flow allows a customer to retain more of the earlier design work. This flexibility makes it possible to select assistance based on project needs, internal skills and available tools.
Depending on the engagement, the work may include:
- Digital and analog design support where skills or tools are limited.
- Physical implementation of digital or mixed-signal designs from VHDL, Verilog RTL or a netlist.
- Low-power implementation techniques.
- Design-for-test insertion, including scan and built-in self-test (BIST), and generation of automatic test pattern generation (ATPG) patterns.
- Identification of suitable intellectual property (IP) blocks for a system-on-chip (SoC).
- Standard-cell library creation or re-characterization.
- Assessment of technology options against performance and price requirements.
Physical design for digital and mixed-signal ASICs
Physical design turns a logical design into a layout that can be manufactured. The work becomes especially involved when a chip combines digital standard-cell logic with analog full-custom blocks, memory macros such as RAM or ROM, and third-party IP such as phase-locked loops (PLLs), analog-to-digital converters (ADCs) or digital-to-analog converters (DACs). These elements must be integrated into a coherent design while meeting the project’s technical constraints.
Integration responsibilities can also be divided in different ways. In an analog-on-top approach, the customer may handle the top-level integration of digital sub-blocks around the analog design. In a digital-on-top approach, a service provider may integrate the digital top-level ASIC and its analog IP blocks. Establishing this boundary early helps clarify ownership of interfaces, integration tasks and deliverables.
Experience across process technologies can matter when selecting an implementation partner. Imec describes its design services as foundry-independent, supporting technologies from 0.7 micrometers to advanced nodes such as FinFET 7 nm. The appropriate technology depends on the design’s requirements; a newer or smaller node is not automatically the right choice for every ASIC.
Low-power techniques and design-for-test
Power management is a design consideration that can influence architecture, implementation and verification. The techniques available for a project may include clock gating, power shut-off, multiple supply voltages, multiple threshold-voltage options and body bias. Their use depends on the design and its operating requirements. Flows such as CPF or UPF can support the expression and management of power intent.
Multi-mode, multi-corner (MMMC) optimization and analysis addresses the need to evaluate a design across multiple operating modes and process, voltage and temperature conditions. This is part of checking that implementation choices remain suitable across the scenarios defined for the chip, rather than only under a single assumed condition.
Test planning is another essential part of ASIC implementation. Scan and BIST structures can be inserted into the design, with ATPG used to create test patterns. Including these capabilities in the design flow connects implementation decisions with the later task of checking manufactured devices. The specific test approach must be matched to the design and its production requirements.
Radiation-hardening and specialized applications
Some ASICs must operate in environments where radiation effects are a design concern. Radiation hardening by design (RHBD) addresses these effects through design choices rather than relying solely on specialized manufacturing processes. Imec’s team describes experience in this area and its collaboration with the European Space Agency on DARE (Design Against Radiation Effects) platforms.
These capabilities are relevant to aerospace, high-energy physics research and medical applications identified by the provider. For teams working in such fields, radiation-related requirements should be considered as part of the design brief and implementation approach.
Connecting design implementation with production
Completing a layout is not the only consideration when planning an ASIC project. Design services can be connected with ASIC services that support foundry technical matters, prototyping, packaging and test, qualification, productization and volume production. Bringing these activities into the project plan can provide a clearer path from design deliverables to manufactured and tested chips.
Imec reports that its design specialists handle more than 40 tape-outs per year across projects for its research organization and external partners, including companies, research institutes and universities. That experience spans different design types and project participants; it does not remove the need to assess a provider’s fit against a particular project’s technology, schedule and responsibilities.
Choosing the right engagement model
Before engaging external ASIC expertise, teams should identify which stages they will own, what inputs they can provide, and which outputs they expect. Key questions include whether support is needed from specification or from an existing RTL or netlist, who will perform top-level integration, and whether test, packaging or production support is part of the required scope.
The practical implication is that ASIC development need not be treated as an all-or-nothing outsourcing decision. A carefully defined engagement can extend a team’s capabilities at selected points in the flow, while broader support can connect specification, implementation and production activities. For industrial automation organizations investing in custom silicon, matching the service model to the design’s technical needs and internal strengths is a useful starting point for managing complexity and moving toward a manufacturable ASIC.