Access Official Technical PDF

Share Summary:LinkedInEmail

Designing an automotive buck converter involves more than stepping a variable input voltage down to a regulated rail. Engineers must also account for load current, efficiency at different operating points, switching noise, thermal management and system start-up behavior. The LM73605-Q1 and LM73606-Q1 synchronous step-down converters address these needs across a 3.5-V to 36-V input range, with output current capability up to 5 A and 6 A, respectively.

The devices are AEC-Q100-qualified for automotive applications and specified for an ambient operating temperature range of –40°C to +125°C. Their shared, pin-to-pin-compatible design allows a choice between the 5-A and 6-A versions when scaling current capacity. Both are offered in a 30-pin WQFN package measuring 6.00 mm × 4.00 mm.

Design flexibility for a wide input range

The LM73605-Q1 and LM73606-Q1 use peak current-mode control and integrate both the high-side and low-side power MOSFETs. Compared with a nonsynchronous buck that uses a discrete diode for the low-side rectifier, this synchronous arrangement can reduce the voltage drop in the freewheeling path. The integrated switches also reduce the number of external power components required.

Output voltage is set using an external feedback resistor divider. Internal compensation helps limit the external circuitry needed for the control loop, while features such as precision enable, power-good monitoring, soft start and tracking give designers options for integrating the converter into a larger power architecture.

The input range and short minimum on-time and off-time support a broad range of conversion conditions. When operating limits are reached at very high or low duty cycles, frequency foldback adjusts switching frequency to extend the regulation range. Actual operating limits still depend on the selected output voltage, input conditions, frequency and external components.

Choosing between auto mode and forced PWM

The SYNC/MODE pin selects how the converter behaves at light loads. In auto mode, the device uses diode emulation: when inductor current falls to zero, the low-side switch turns off. At very light loads, the converter can reduce switching frequency using pulse-frequency modulation (PFM), reducing switching activity to support light-load efficiency.

Forced pulse-width modulation (FPWM) keeps the switching frequency set by the RT resistor or external clock across the load range. The inductor current can become negative at light loads, so this mode may have lower light-load efficiency than auto mode. Its consistent frequency can be useful when a design requires a fixed switching pattern. The mode choice primarily affects lighter-load behavior; above the relevant discontinuous-conduction and frequency-foldback boundaries, operation is similar.

Set switching frequency to match system priorities

An external resistor on the RT pin sets switching frequency from 350 kHz to 2.2 MHz. If RT is left open, the nominal default is 500 kHz. The converter can also synchronize to an external clock within the supported frequency range, allowing its switching activity to be coordinated with a system clock.

Frequency selection is a design trade-off, not a standalone optimization. Lower frequency generally reduces switching losses, while higher frequency can allow smaller inductors and output capacitors. The appropriate setting depends on the input and output voltage ranges, typical load, component selection, efficiency goals, thermal constraints and solution-size requirements. Engineers should also check minimum on-time and off-time limits across the intended operating range.

Manage start-up, sequencing and bias power

The SS/TRK pin supports the device’s internal soft-start ramp, an extended ramp using an external capacitor, or output-voltage tracking from an external ramp. Soft start controls how quickly the output rises and can help manage inrush current during start-up. The converter can also start into a pre-biased output, an important condition to consider when multiple rails or stored output charge are present.

The precision enable input can be driven directly or configured with a resistor divider to establish a system undervoltage lockout threshold. This can support power sequencing or define the input voltage at which the regulator starts. The enable pin should not be left floating.

An optional BIAS input provides another way to manage internal LDO power loss. When the output is between 3.3 V and 18 V, the recommended connection is to tie BIAS to VOUT. If a suitable external 3.3-V or 5-V rail is available, it can also supply BIAS, provided the pin voltage does not exceed VIN. Tie BIAS to ground when it is unused. Any use of this pin should be checked against the device’s operating conditions and the application’s power design.

Protection and PCB implementation matter

Built-in protection includes input undervoltage lockout, cycle-by-cycle current limiting, hiccup short-circuit protection and thermal shutdown. The open-drain PGOOD output indicates whether the output is within its monitored regulation window; it requires a suitable pull-up supply and current-limiting resistor. These functions provide useful system status and fault response, but do not replace application-level validation.

PCB layout is central to achieving the intended electrical and thermal behavior. The input bypass capacitor should be placed close to the PVIN and PGND pins with short, wide connections. The exposed die-attach pad is a major heat path and should connect to system ground copper; thermal vias are preferred to help transfer heat to other board layers. Keep the feedback divider near FB and route its feedback node away from noisy switching areas. Follow the device documentation for component placement, grounding and routing details.

Practical implications for power-system design

The LM73605-Q1 and LM73606-Q1 combine a wide input range, integrated synchronous switches, adjustable frequency and configurable light-load behavior in a compact package. For engineers and system integrators, the practical task is to match those options to the application: choose the current grade, assess auto mode versus FPWM, select a switching frequency, define start-up and enable behavior, and verify thermal and layout requirements. Careful evaluation of the complete operating range helps turn the converter’s flexibility into a robust, application-appropriate power supply.

Access Official Technical PDF

About The Author