Access Official Technical PDF

Share Summary:LinkedInEmail

Automotive current monitoring has to serve two different purposes in a motor drive: provide a usable signal for control and monitoring, and help shut down the power stage when current becomes unsafe. A low-side shunt circuit can address both needs by combining an amplifier and an analog-to-digital converter (ADC) path with a separate comparator-based protection path. In the described architecture, a shunt measures inverter current, while comparators and logic act on an overcurrent or short-circuit condition without relying on the microcontroller to make the immediate shutdown decision.

How a low-side current shunt measures inverter current

A shunt resistor converts current into a small voltage drop. Measuring the voltage across the resistor therefore provides a signal corresponding to the current flowing through the inverter. Because this signal is low in amplitude, the differential amplifier used to measure it needs low noise and low offset; otherwise, those errors can degrade the measured signal.

The amplifier also needs to respond quickly. Fast settling time and high slew rate help it follow changes in the shunt voltage, while sufficient bandwidth supports a high-gain signal path. In the circuit, the OPA365-Q1 amplifies the differential shunt measurement and feeds both a comparator circuit and the ADC input of a C2000 microcontroller.

Why the reference voltage matters

The shunt current can flow in either direction, so the amplified signal must be able to represent both polarities. A TLV314-Q1 is configured as a voltage follower to provide a stable reference at half the supply voltage, or VCC/2. The OPA365-Q1 output is then centered around this reference: for one current direction, it can range from VCC/2 toward VCC; for the other, it can range from VCC/2 toward ground.

This midpoint reference lets a single-supply signal path indicate current changes in both directions. The TLV314-Q1 is selected for stable unity-gain operation and its ability to drive capacitive loads up to 300 pF in the described circuit.

Amplifier performance for fast current measurement

The OPA365-Q1 specifications illustrate the characteristics considered for this application. It has 50 MHz of bandwidth, input voltage noise of 4.5 nV/√Hz at 100 kHz, and an offset of 100 μV. Its settling time is 0.3 μs to 0.01%, and its slew rate is 25 V/μs. These characteristics support amplification of the shunt signal for both digitization and threshold detection.

The device is specified for an ambient temperature range of -40°C to 125°C and is AEC-Q100 Grade 1 qualified for automotive applications. These specifications describe the component; the complete circuit still needs to be designed and evaluated for its intended operating conditions.

Separating current monitoring from fault shutdown

The C2000 TMS320F28052 microcontroller receives the amplified shunt signal at its ADC. The source design identifies its ADC as 12-bit, with a 3.75-MSPS sampling rate. This path can be used to monitor or log shunt current as part of motor-control or digital-power functions.

For a fault response, however, the circuit also uses two LMV393-Q1 comparators. Their thresholds correspond to overcurrent conditions. One comparator is configured in an inverted arrangement so the circuit can detect current peaks in the opposite shunt-current direction. When a threshold is crossed, the relevant comparator changes state.

This separation is important to the architecture: the comparator path can initiate shutdown directly, rather than waiting for the microcontroller to sample the signal, process it and issue a control command. The design describes this as a way to disable the gate drivers much faster than the MCU.

How the shutdown logic disables gate-driver signals

The comparator outputs trigger an SN74LVC2G74-Q1 D flip-flop. In response, the flip-flop disables a buffer between the microcontroller and the gate drivers. When the buffer is disabled, low-side resistors connected to the control lines pull the gate-driver input signals down. The gate drivers then turn off the system’s insulated-gate bipolar transistors (IGBTs).

The resulting chain is straightforward:

  • The shunt voltage represents inverter current.
  • The amplifier scales the differential signal around VCC/2.
  • The ADC path supplies current information to the microcontroller.
  • The comparators detect configured overcurrent thresholds in either current direction.
  • The flip-flop and buffer control the gate-driver signals so the IGBTs turn off during a detected fault.

This approach makes measurement and protection complementary but distinct. The MCU receives a signal for monitoring, while the analog comparator and logic path provides a direct route to gate-driver shutdown.

Design implications for automotive motor drives

The circuit was featured in a reference design for a high-voltage, high-power automotive HVAC compressor drive. That design uses a three-phase inverter with discrete IGBTs to drive a brushless DC motor using sensorless torque control. The monitoring circuit illustrates how current sensing can be integrated into an automotive motor-drive system, but its component choices and thresholds should be assessed in the context of the specific application.

For engineers and system integrators, the practical takeaway is to treat current measurement and fault response as related design tasks with different timing needs. The amplifier must preserve a small shunt signal well enough for the ADC and comparators, while comparator thresholds and shutdown logic must be arranged to respond to faults in both current directions. The gate-driver interface and pull-down behavior are also part of the protection chain, not details to leave outside the analysis.

In short, a low-side shunt, a suitably fast amplifier, dual comparators and a D flip-flop can form a coordinated approach to automotive current monitoring: the microcontroller receives current data, and a separate hardware path can disable gate-driver signals when an overcurrent or short-circuit condition is detected.

Access Official Technical PDF

About The Author