Automotive radar beamsteering can help a corner sensor direct its detection field across different azimuth angles rather than concentrating on a single fixed direction. Texas Instruments’ TIDEP-01021 reference design demonstrates this approach with the AWR1843 evaluation module, combining frequency-modulated continuous-wave (FMCW) radar, transmit beamforming and two operating modes intended for applications such as blind spot detection (BSD), lane change assist (LCA), traffic jam assist (TJA) and cross traffic alert (CTA).
For engineering teams, the design is useful as a starting point for understanding how sensing range, range resolution, velocity measurement and field of view depend on radar configuration. It is a reference implementation, not a guarantee that a finished sensor will deliver the same results in every vehicle, antenna layout or operating environment.
How automotive radar beamsteering works
The AWR1843 has three transmitters and four receivers. In the design’s BSD, LCA and TJA mode, all three transmitters operate simultaneously. Their transmitted signals are configured with relative phase offsets so they combine to focus the beam in a selected direction. The device’s six-bit TX phase shifter provides phase settings in 5.625-degree increments.
The reference design uses frame-based steering: chirps within a given subframe use the phase settings for the same steering angle. The demo steps through angles from -60 to +60 degrees in 20-degree increments, then returns to the starting angle. A complete sweep takes approximately 200 milliseconds. The steering angle and step size can be changed in the demo software.
This is different from time-division multiplexed multiple-input, multiple-output (MIMO) operation. In the design’s ultra-short-range radar (USRR) mode, the transmitters take turns transmitting on successive chirps. Processing the signals from the different transmitters and receivers creates a virtual antenna array, supporting improved angular resolution at shorter range.
Two modes balance range and resolution
The design combines long-range short-range-radar operation with a higher-resolution USRR profile. The two profiles use different chirp settings because a radar configuration suited to detecting distant vehicles is not equally suited to resolving closely spaced objects nearby.
- BSD, LCA and TJA profile: Targets a maximum range of 150 metres at boresight for an object with an approximately 10 m² radar cross section. The listed range resolution is about 0.75 to 0.78 metres.
- USRR profile: Targets a maximum range of 30 metres, with range resolution of approximately 4.3 centimetres. Its listed maximum velocity is 36 km/h, compared with 144 km/h for the long-range profile after velocity disambiguation.
These figures describe different configurations, not simultaneous performance at every distance. The design uses an advanced frame configuration with separate subframes for the long-range and USRR contexts. This multi-mode approach provides a long-range view alongside a denser point cloud at shorter range.
Range, resolution and velocity are connected to choices such as chirp slope, bandwidth, sampling and chirp repetition timing. For example, the long-range profile uses a lower frequency slope to stay within the device’s 10 MHz intermediate-frequency bandwidth while targeting 150 metres. Its range resolution is consequently coarser than that of the short-range profile.
From radar samples to object tracks
Signal processing turns the received radar data into detections that downstream applications can use. The hardware accelerator performs range FFT processing, while the DSP and accelerator handle later stages. Enhanced Direct Memory Access (EDMA) moves data between memory locations so processing resources can continue working while transfers take place.
The processing chain includes velocity estimation, detection, angle estimation and filtering to reduce ground clutter. Detected objects are grouped using the dBScan clustering algorithm. In the USRR mode, clusters can be presented as groups of nearby points; in the long-range mode, a representative object from a cluster can be passed to the tracker.
Tracking uses an extended Kalman filter with position and velocity states. Its data association logic links new measurements to existing tracks, so assumptions about object motion matter. The reference design’s initialization assumes that an object’s velocity is along the radar’s longitudinal axis. That assumption is more appropriate for long-range traffic moving toward or away from the sensor than for cross traffic. Integrators adapting the design should review initialization and association logic for their intended scene and application.
What the beamsteering test results show
The reference design compares beamsteering and non-beamsteering demonstrations using an AWR1843BOOST evaluation module. The reported test placed the sensor on a tripod and measured maximum detection range for mid-size SUVs at different angles. At boresight, both approaches detected to 160 metres. Results were also the same at the tested angles through ±40 degrees.
At ±50 degrees, the reported maximum was 75 metres with beamsteering versus 45 metres without it. At ±60 degrees, the corresponding results were 50 and 30 metres. These measurements indicate that steering extended detection range at the wider tested angles in this setup; they should not be interpreted as a general performance guarantee or as proof of improvement across all angles and installations.
Practical considerations for integration
Teams evaluating the design should treat chirp configuration, antenna geometry, memory use and tracking assumptions as parts of one system-level decision. The AWR1843 has limited on-chip memory, and the reference implementation manages processing buffers by reusing memory between stages and subframes. Adding modes or changing processing can affect those allocations and EDMA configuration.
Beamsteering also changes where the sensor concentrates its transmit energy over time. The reference design scans in discrete angle steps, so application teams need to consider how that scan schedule fits the intended detection and tracking requirements. The supplied software and evaluation hardware offer a way to explore configuration and visualize point clouds, clusters and tracks before developing a standalone sensor.
Conclusion
TIDEP-01021 illustrates how automotive corner radar can combine TX beamforming, azimuth beamsteering and distinct long- and short-range profiles on a single radar platform. Its practical value lies in showing the relationships between chirp design, detection trade-offs, signal processing and tracking—not in providing a universal configuration. For integrators, the key next step is to validate the radar profile, steering schedule and motion assumptions against the application’s actual coverage and operating conditions.