Access Official Technical PDF

Share Summary:LinkedInEmail

A cascaded H-bridge inverter uses series-connected power cells to produce a stepped AC voltage from separate DC sources. For engineers working on renewable-energy conversion, power conditioning, or other medium- and high-power systems, the choice of switching strategy affects the output waveform and its harmonic content. A MATLAB/Simulink comparison of carrier-based pulse-width modulation (PWM) methods for a five-level cascaded H-bridge inverter reports lower output-voltage total harmonic distortion (THD) with level-shifted sinusoidal PWM than with the phase-shifted method and two other level-shifted variants.

How a cascaded H-bridge inverter creates voltage levels

A multilevel inverter combines switching cells to generate an output voltage in several discrete steps rather than switching only between two voltage states. In a cascaded H-bridge (CHB) design, each cell is an H-bridge supplied by a DC source. Connecting cells in series allows their output voltages to add or subtract, creating a stepped waveform that approximates a sine wave.

For a symmetrical CHB inverter, the DC sources have equal voltage amplitudes. The study describes a five-level arrangement with two H-bridge cells per phase and two equal, independent DC sources. Its output levels are +2V, +V, zero, -V, and -2V. In the paper’s notation, the number of levels is 2m + 1, where m is the number of DC sources. A seven-level output can therefore be formed with three sources, assuming the same symmetrical arrangement.

Adding output levels can make the voltage waveform more closely resemble a sine wave and can reduce harmonic distortion. The CHB structure also has a modular arrangement. Its trade-offs include the need for multiple DC sources and coordination between the switching signals for the individual bridges.

PWM’s role in shaping the output

Sinusoidal PWM compares a low-frequency sinusoidal reference signal with one or more high-frequency triangular carrier signals. The comparison determines when inverter switches change state, and the resulting pulse widths shape the output voltage. The reference frequency sets the output frequency, while its amplitude relative to the carrier affects the modulation index and the output voltage.

In a multilevel inverter, carrier-based PWM uses multiple carriers to select among the available voltage levels. The study compares level-shifted methods—phase disposition (PD), phase opposition disposition (POD), and alternate phase opposition disposition (APOD)—with phase-shifted PWM.

How the carrier arrangements differ

  • PD: The high-frequency carrier signals are in phase with one another.
  • POD: Carriers above the zero reference are in phase with each other, while those below it are shifted by 180 degrees.
  • APOD: Each carrier is shifted by 180 degrees relative to the adjacent carrier.
  • Phase-shifted PWM: Carrier signals are phase-shifted relative to one another. The study notes this approach is used in cascaded inverters and discusses its potential for reducing output harmonics while distributing power among cells.

For five voltage levels, the described carrier arrangement requires four high-frequency carrier signals: one fewer than the number of output levels. Comparing the reference with these carriers determines which of the five voltage steps the inverter produces at a given instant.

Five-level inverter simulation and reported THD

The study models a three-phase, five-level CHB inverter in MATLAB/Simulink and compares output-voltage waveforms using different multicarrier PWM approaches. Its stated simulation parameters are a 200 V DC source value, a 5 kHz carrier frequency, a 50 Hz reference frequency, and a modulation index of 0.9. The reported comparison uses line-to-line output-voltage THD.

The results list the following THD values:

  • Level-shifted SPWM: 17.51%
  • Phase-shifted SPWM: 30.39%
  • POD-SPWM: 28.89%
  • APOD-SPWM: 28.75%

Within this simulated setup, level-shifted SPWM has the lowest reported THD among the four methods. The paper identifies its PD implementation as the best-performing approach in the comparison. These figures describe the specific model and operating parameters reported; they should not be treated as universal performance values for every CHB inverter or application.

What the comparison means for design decisions

For system integrators and power-conversion engineers, the results illustrate why PWM selection should be evaluated against the intended topology and operating conditions rather than assumed from the method’s name alone. A lower simulated THD may be relevant when assessing waveform quality, but it is only one part of a design decision. The chosen strategy must also work with the available DC sources, the required output levels, and the coordination needs of the bridge cells.

Simulation provides a useful way to compare modulation schemes before implementation. Engineers can examine the generated voltage waveform and its harmonic spectrum under consistent model conditions, then validate the selected control approach against the requirements of the target system. The reported comparison does not establish performance under every load or operating condition, so its numerical results should be interpreted within the scope of the simulation.

Conclusion

A five-level cascaded H-bridge inverter builds a stepped AC output by combining the contributions of two H-bridge cells per phase. Multicarrier SPWM controls how the inverter moves between those voltage levels, and the carrier arrangement influences the resulting harmonic profile. In the reported MATLAB/Simulink comparison, level-shifted SPWM produced 17.51% line-to-line voltage THD, lower than the values listed for phase-shifted, POD, and APOD PWM. For engineers evaluating CHB control, the practical takeaway is to compare modulation options in the context of the actual topology and operating requirements, using simulation as a design aid rather than as a substitute for application-specific validation.

Access Official Technical PDF

About The Author