Multiplication is a core operation in digital signal processing and other compute-intensive electronics, but its implementation can affect circuit power, speed, and silicon area. The CCA multiplier, or cascade carry array multiplier, is a 4×4-bit unsigned design that aims to improve these measures by reducing the number of adder units in the multiplier structure. In HSPICE simulations, it used less power and had shorter propagation delay than five conventional comparator designs under the conditions evaluated.
For industrial automation engineers and system designers, the results are relevant when assessing arithmetic blocks in embedded electronics, DSP hardware, or other systems where power and latency are design constraints. They are simulation results for a specific circuit and process, however, not a general performance guarantee for every implementation.
Why multiplier architecture affects circuit performance
A digital multiplier forms partial products from its input bits and combines them using adder stages. The arrangement of those stages influences how much logic a signal must pass through before the output is ready. More circuitry can also increase internal capacitance and switching activity, both important considerations in CMOS power consumption.
Propagation delay is the time required for a change at the input to affect the output. In a multiplier, signals may pass through several adder units, so the architecture and number of stages in the critical path can influence the result. Switching delays can also create transient changes, often called glitches, which contribute to power dissipation.
These trade-offs are familiar in digital design: a circuit must meet timing requirements while managing power and area. Power-delay product (PDP) combines average power and delay into one comparison metric; energy-delay product (EDP) provides another measure for evaluating energy and timing together. Neither metric alone replaces application-specific design validation.
How the CCA multiplier is structured
The proposed design focuses on a 4×4-bit multiplier and seeks a logical arrangement that uses fewer adder units along the input-to-output path. Its authors selected a conventional 28-transistor CMOS full-adder cell for the compared multiplier implementations, citing its output swing and delay characteristics as reasons for the choice.
Rather than relying on extra adder units, the cascade carry array structure organizes the arithmetic to reduce the required count. The paper presents this as the basis for lowering transistor count, propagation delay, and power relative to the comparator architectures. The evaluation covers array, Braun, ripple carry array (RCA), row-bypassing RCA, and carry-save array (CSA) bypassing multipliers.
CCA multiplier simulation results
The designs were simulated in HSPICE using 0.18 µm CMOS technology, a 1.8 V supply, a 100 MHz clock frequency, and an operating temperature of 27°C. The reported figures are specific to these simulation conditions.
- Average power: The CCA design measured 112.24 µW, compared with 126.60 µW for RCA and 164.84 µW for bypassing RCA.
- Propagation delay: The reported CCA delay was 351.5 ps. Bypassing RCA measured 509 ps, while RCA measured 521.5 ps.
- Power-delay product: CCA recorded 39.45 fJ, versus 66.02 fJ for RCA and 83.90 fJ for bypassing RCA.
- Transistor count: The CCA implementation used 436 transistors. Array, Braun, and RCA each used 464; bypassing RCA used 655, and bypassing CSA used 810.
Against bypassing RCA, the paper reports approximately 31% lower propagation delay and 32% lower power for CCA. Its transistor count was also lower, by 219 transistors in the reported comparison. These figures describe the evaluated 4×4 implementations and should not be extrapolated directly to other bit widths or process technologies.
What the results mean for design decisions
The results illustrate why multiplier architecture is worth considering alongside the choice of full-adder cell. Reducing the number of adder units can affect several linked measures: fewer transistors may mean less internal capacitance, while a shorter or more efficient signal path can reduce delay. The study’s CCA results show improvements in power, delay, PDP, and transistor count within its test setup.
For a design team, the practical next step is to treat these figures as a point of comparison, then validate the intended implementation under its own requirements. Important considerations include:
- Whether the 4×4-bit unsigned arithmetic function matches the application.
- How the selected architecture behaves at the required bit width and in the target technology.
- Whether timing, power, area, and output-swing requirements are met together.
- How the circuit performs when integrated into the broader design and evaluated using representative operating conditions.
The study does not establish that CCA is the best choice for every multiplier, workload, or fabrication process. Its results are bounded by the specified simulation setup, and additional validation is needed before applying them to a particular product or system.
Conclusion
The cascade carry array multiplier offers a 4×4-bit approach that reduces the adder-unit and transistor counts while improving simulated power and propagation delay compared with the architectures evaluated. For engineers working on embedded arithmetic or DSP circuitry, it highlights the value of structural optimization—not just component selection—when balancing speed, power, and area. The reported HSPICE results provide a useful comparison baseline, but application-specific simulation and verification remain essential before design adoption.