Access Official Technical PDF

Share Summary:LinkedInEmail

In cadmium telluride (CdTe) thin-film solar cells, absorber grain structure matters because grain boundaries can contribute to carrier recombination. Larger grains may reduce overall grain-boundary density, but growing them during deposition can require elevated temperatures that are not suitable for every manufacturing approach or substrate. Research on CdTe grain growth shows that post-deposition CdCl2 treatment can substantially reshape films initially deposited at different temperatures, offering a way to adjust morphology after absorber formation.

The findings also have a practical measurement implication: etched-surface optical microscopy can provide a faster, lower-cost way to estimate grain size than relying exclusively on electron backscatter diffraction (EBSD). It does not replace EBSD, but comparison between the methods supports its use for rapid assessment.

Why grain structure matters in CdTe absorbers

CdTe absorbers are polycrystalline, so their grains meet at boundaries that can act as recombination sites. The grain structure can therefore influence minority-carrier lifetime and, in turn, photovoltaic device performance. In close-spaced sublimation (CSS) films, grains may be relatively small near the window-layer interface, where nucleation occurs, even when grains farther through the film are larger. This makes it important to consider the absorber’s structure across its thickness, not just at the exposed back surface.

Deposition temperature is one factor that shapes the as-grown film. In the study, CSS CdTe deposited at a higher temperature began with larger grains than material deposited at a lower temperature. However, the initial difference did not determine the final grain size after chloride treatment: grains in lower-temperature films grew during recrystallization and became comparable in size to those from higher-temperature depositions under the examined conditions.

CdTe grain growth during CdCl2 treatment

Researchers compared low- and high-temperature CSS deposition conditions using CdTe films on CdSe and magnesium zinc oxide (MZO) window layers. CdCl2 treatments lasted 10 minutes, with treatment temperatures ranging from 400°C to 475°C. Across the tested films, average grain size increased as treatment temperature rose. Cross-sectional EBSD also showed recrystallization and changes in grain orientation after treatment.

At lower treatment temperatures, small grains and horizontal grain boundaries could remain near the window-layer interface. Increasing the treatment temperature generally promoted grain growth and reduced these interface features. Their persistence depended in part on the initial deposition condition: low-temperature CdTe on MZO required more aggressive treatment to reduce small interface grains than high-temperature CdTe. The results demonstrate that deposition history still matters, even though both types of films can reach similar grain sizes after treatment.

These observations should not be read as a universal instruction to maximize annealing temperature. In CdSe-based films, thinner window layers could support large grains extending from the interface toward the back of the absorber at higher treatment temperatures, while thicker CdSe showed greater resistance to delamination and film degradation at elevated temperatures. The work identifies an intermediate CdSe thickness of roughly 150–200 nm as a potentially suitable balance in the tested context. The tradeoff illustrates why absorber recrystallization must be considered alongside the stability and morphology of the full layer stack.

Relating grain size to carrier lifetime

Minority-carrier lifetime was measured using time-resolved photoluminescence (TRPL). Across the samples, longer measured lifetimes were associated with larger grains. This relationship is consistent with lower grain-boundary density and improved interface morphology contributing to reduced recombination. The study also notes that CdCl2 treatment can affect defects through mechanisms such as grain-boundary passivation and reduction of defects within grains; grain growth is not the only possible influence on lifetime.

The TRPL decay behavior and the observed grain-size trend support the importance of grain-boundary recombination, but the measurements do not isolate every contribution. Changes in interface and bulk lifetimes may be intertwined. For process development, grain size is therefore a useful structural indicator, not a complete substitute for electrical characterization.

Results across CdSe and MZO window-layer devices also indicated that selenium interdiffusion was not the primary factor governing the grain structures and lifetimes in these experiments. This narrows the interpretation of the observed trends without establishing that interdiffusion is irrelevant in all CdTe device designs or processing conditions.

Using optical microscopy for faster assessment

EBSD can map grain orientation and structure through a film, but it requires specialized equipment, sample preparation, and analysis. The optical method developed in this work uses a brief preferential etch to reveal grain boundaries on the exposed CdTe surface, followed by microscope imaging and standard grain-size analysis. Optical estimates compared favorably with EBSD measurements, providing corroboration for the approach.

For process teams screening multiple samples, this method can support faster comparisons of grain-size distributions after changes to deposition or annealing conditions. It is most useful when interpreted with awareness of what it measures: surface grain structure. Mechanical beveling or focused ion beam preparation can reveal structure through the film thickness, while cross-sectional EBSD provides additional information about interface grains and orientation.

Practical implications for process development

  • Assess the full thermal sequence. Initial CdTe deposition temperature does not alone predict the final grain size; CdCl2 treatment temperature also plays a major role.
  • Inspect the interface as well as the back surface. Small grains and horizontal boundaries near the window layer may persist even when surface grains appear larger.
  • Balance recrystallization with layer stability. Raising treatment temperature can encourage growth, but window-layer thickness and resistance to degradation are also relevant.
  • Use complementary characterization. Optical microscopy can accelerate screening, while EBSD and TRPL provide structural and lifetime information that surface imaging alone cannot supply.

For engineers and technical decision-makers developing CdTe thin-film processes, the central lesson is that lower-temperature deposition does not necessarily lock an absorber into a finer final grain structure. CdCl2 recrystallization can produce substantial growth, and larger grains correlate with longer measured lifetimes. The practical opportunity is to tune deposition, window-layer design, and post-deposition treatment together, using rapid microscopy for screening and deeper structural and electrical measurements to verify the outcome.

Access Official Technical PDF

About The Author