Access Official Technical PDF

Share Summary:LinkedInEmail

Colloidal quantum dot solar cells offer a route to photovoltaic devices whose light absorption can be tuned through nanocrystal size. This spectral flexibility is particularly relevant to infrared harvesting and tandem architectures, while solution processing offers a different manufacturing pathway from conventional wafer-based approaches. Realizing these advantages depends on solving persistent materials and device challenges: surface trap states, limited carrier mobility and energetic disorder can all impede the collection of photogenerated charge.

Research into CQD photovoltaics highlights three complementary levers for improvement: engineer the junction so carriers are extracted more effectively, make the quantum-dot film’s energy landscape more uniform, and develop surface treatments or hybrid structures that support transport without sacrificing passivation.

Why quantum dots are useful in photovoltaics

Colloidal quantum dots are semiconductor nanocrystals only a few nanometers in size. At these dimensions, quantum confinement makes their bandgap dependent on particle size. Selecting different sizes therefore provides a way to adjust the wavelengths a CQD film absorbs, including infrared portions of the solar spectrum. That tunability makes CQDs candidates for both single-junction solar cells and tandem devices paired with wider-bandgap absorbers.

CQDs can be deposited from solution, and their surfaces can be chemically modified with ligands. These features make them adaptable as active layers and enable processing strategies that are difficult to apply in the same way to bulk semiconductors. However, a film must do more than absorb light: it must also separate and transport charge carriers to the device contacts before they recombine.

Colloidal quantum dot solar cells: the transport challenge

As-synthesized dots are commonly surrounded by relatively long organic ligands. These ligands help stabilize the nanocrystals, but they can also keep neighboring dots far apart and create barriers to charge movement. Replacing them with shorter ligands can bring dots closer together and improve electronic coupling. Yet ligand exchange can expose or create surface defects, increasing trap-state density and the likelihood of carrier loss.

Energetic disorder adds another complication. Variations in dot size, packing and surface chemistry can create a spread of energy states, including bandtail states near the band edge. Carriers may move into lower-energy regions within this landscape and become less available for collection. Consequently, improving charge transport requires attention to both inter-dot barriers and the uniformity and passivation of the film.

Three strategies for improving CQD photovoltaic performance

1. Design the junction to improve charge extraction

One approach is to modify the electron-accepting layer rather than relying only on changes to the CQD absorber. Increasing the carrier density of a zinc oxide electron-transport layer can alter the device’s depletion profile. In the reported double-sided-junction design, this engineering increased the width of the depleted region across the CQD layer and reduced the quasi-neutral portion of the absorber under operating conditions.

The practical objective is to make a larger share of the active layer more favorable for charge separation and extraction, while limiting recombination. This illustrates why electrode and transport-layer properties matter alongside absorber composition: device architecture helps determine whether carriers generated in the CQDs can reach the contacts efficiently.

2. Flatten the energy landscape with solution-phase ligand exchange

Ligand exchange performed in solution offers another way to prepare CQD absorber films. In contrast to layer-by-layer deposition followed by solid-state treatment, the dots are exchanged before film formation and then deposited as an active layer. This method was used to produce films with improved surface passivation and a more uniform energy landscape, addressing both trap-related losses and energetic disorder.

A flatter energy landscape can reduce energy funneling among dots and support carrier diffusion through the film. The work reported certified solar power conversion efficiency of 11.3% for devices made using this approach. That result is evidence of the potential of coordinated materials processing; it should not be taken to mean that ligand exchange alone determines performance, since the complete device stack and operating conditions also matter.

3. Adapt surface chemistry for infrared CQDs

Extending a ligand-exchange method to larger, small-bandgap CQDs is not automatic. Infrared-absorbing dots create specific surface-management challenges: the treatment must passivate the surface while avoiding excessive fusion between particles. Work on short-chain carboxylate ligands, including formate-assisted exchange, investigated this balance in PbS CQDs.

In the reported field-effect transistor measurements, formate-exchanged films had an electron mobility of 0.02 cm2 V-1 s-1, twice the value measured for acetate counterparts, along with a trap-state density of 7.6 × 1015 cm-3. These measurements characterize the films and transport behavior; they are not, by themselves, a guarantee of the same improvement in every solar-cell architecture. The broader lesson is that surface chemistry needs to be tailored to dot size and application rather than transferred unchanged between CQD systems.

Hybrid matrices as a route to mobility and stability

A further strategy combines CQDs with epitaxially grown inorganic metal halide perovskites. In this hybrid system, the perovskite forms a matrix around the dots. The matrix can passivate CQD surfaces and provide an additional pathway for carrier transport, while the interface and lattice match influence the resulting material properties.

The reported matrix-passivated films showed approximately twice the carrier mobility of pristine CQD films and superior thermal stability compared with the unmodified dots. These findings point to a design opportunity: the surrounding material can be an active part of the transport and stability strategy, rather than simply a passive layer in the device.

Practical implications for photovoltaic development

For engineers and technical teams assessing CQD absorbers, the findings suggest several useful considerations:

  • Evaluate the full device stack. Transport-layer doping and junction geometry can affect depletion, recombination and charge extraction.
  • Balance conductivity with passivation. Shorter ligands may improve inter-dot transport, but surface defects must also be controlled.
  • Account for energetic disorder. Film uniformity and bandtail states influence how effectively carriers diffuse toward contacts.
  • Match processing to absorber size. Approaches that work for one CQD bandgap may require adjustment for infrared dots.
  • Consider the matrix material. Hybrid structures can influence both mobility and thermal stability, with interface properties playing an important role.

Colloidal quantum dot solar cells are promising because their absorption can be tuned and their active layers processed from solution, but those characteristics alone do not ensure efficient operation. Progress depends on integrating junction design, ligand chemistry and film structure to reduce recombination and improve transport. For photovoltaic developers, the practical takeaway is to treat the absorber, its surface and the surrounding device layers as a connected system—one in which improvements in charge extraction, passivation and stability must work together.

Access Official Technical PDF

About The Author