Compound semiconductor RF applications span mobile networks, satellite communications, defence systems, automotive electronics and industrial test equipment. For engineers and technical decision-makers, the choice of device material is shaped by the job: operating frequency, power requirements, system architecture and, in some markets, manufacturing and qualification constraints. Gallium arsenide (GaAs) remains central to many RF front ends, while gallium nitride (GaN) is gaining ground in high-power applications.
The industry landscape described here reflects the market outlook and forecasts published in the source study, which largely date from 2016–2018 and project forward to 2024. Those figures should be read as period estimates, not as current market data. The technical and supply-chain themes, however, show how varied the demands on RF and microwave components can be.
Compound semiconductor RF applications: matching materials to system needs
Compound semiconductor devices are used where RF systems require performance that silicon alternatives may not provide as effectively for a particular application. GaAs has a long-established role in mobile-device power amplifiers and switches. GaN is particularly relevant where high power density and power handling are priorities, including base stations, radar and some satellite systems. Silicon LDMOS remains an alternative in parts of the cellular infrastructure market, especially at lower frequencies.
These materials do not map neatly onto a single market. A handset, a radar array and a satellite payload face different operating conditions and design trade-offs. Device selection therefore depends on the requirements of the complete RF chain, rather than on material properties in isolation.
Telecom infrastructure and connected devices
Cellular communications have historically been a major source of RF compound semiconductor demand. Handsets must support multiple bands and, during technology transitions, may need to remain compatible with earlier generations of mobile networks. The study identifies GaAs power amplifiers and switches as established handset technologies, while noting that GaN’s operating voltage makes it less suited to battery-powered handsets.
Network infrastructure presents a different opportunity. Base stations need power amplifiers, and the study describes a shift toward GaN in some infrastructure applications, alongside continued use of LDMOS. More numerous small cells, remote radio units and microwave or millimetre-wave backhaul links also create requirements for RF components. As networks evolve toward higher frequencies and more complex architectures, test equipment must support those systems too.
Industrial IoT and machine-to-machine connectivity use a mix of cellular, local-area and low-power wide-area technologies. Many individual connected devices are likely to use silicon to meet cost requirements, while the network infrastructure can rely on compound semiconductor devices. For industrial automation, this distinction matters: an IoT deployment may involve many inexpensive endpoints, but still depend on capable RF infrastructure and gateways.
Satellite, defence and automotive systems
Satellite communications
Satellite applications impose demanding conditions, including radiation exposure in space systems, limited power budgets and the need to qualify technologies for use in space. GaAs has a long-standing role in satellite electronics and amplifiers. The study identifies GaN as a potential option for higher power density and more compact systems, including as a solid-state alternative to travelling-wave tube amplifiers in some applications. Adoption depends on development and qualification, not just device performance.
Defence and security
Defence applications include radar, electronic warfare, communications and navigation. These systems may require high power over a relatively narrow bandwidth, as in radar, or wide bandwidth, as in electronic warfare and countermeasures. GaAs devices are established in military sensors, while GaN is being applied to solid-state power amplifiers and active electronically scanned array radar. The study also highlights drone detection and mitigation as an emerging area of demand.
Defence supply chains combine large system integrators, specialist component suppliers and, in some cases, in-house manufacturing. Commercial off-the-shelf devices can also be used where appropriate, subject to any required qualification. For UK organisations, the study points to the strategic importance of domestic design capability and access to suitable manufacturing.
Automotive electronics
Automotive RF systems include vehicle radar, telematics, keyless entry and connected-car communications. The study describes established use of millimetre-wave radar for driver assistance and the growing interest in connected and autonomous vehicles. It also notes that different semiconductor technologies are used across these functions: GaAs has supported some radar chipsets, while silicon-germanium solutions are also marketed for automotive radar.
Industrial instrumentation and specialist uses
Test and measurement is an important, sometimes underestimated, application for RF devices. Signal generators, spectrum and signal analysers, vector network analysers and wireless testers use RF components in their front ends. These instruments must support stable, repeatable measurements, including at frequencies used by newer wireless systems. The study also describes a move toward virtual or synthetic instruments, in which measurement functions and post-processing are implemented on more general-purpose hardware.
Other specialist applications include medical diathermy, where RF or microwave energy is used for therapeutic heating, and emerging agricultural sensing. The source notes that solid-state GaN amplification could be an alternative to magnetrons in some medical equipment if it becomes sufficiently cost-effective. It also identifies university development of microwave and terahertz sensors for agriculture.
What the supply chain means for the UK
The UK’s position in the landscape described by the study is strongest in research, device and subsystem design, integration, prototyping and low-volume production. The study reports that large-scale domestic RF integrated-circuit fabrication had declined, leaving many UK design companies reliant on merchant foundries in the United States or Asia-Pacific. It also identifies concerns around intellectual property, ownership, export controls and the ability to scale production.
This structure has practical implications. Access to fabrication, packaging expertise and production partners can affect how easily a design moves from prototype to volume manufacturing. The study also emphasizes university-industry collaboration and the need to develop technical skills across research, design and manufacturing.
Conclusion
Compound semiconductor RF applications serve markets with very different performance and production requirements. GaAs remains important in mobile RF front ends, while GaN is expanding in high-power infrastructure, defence and satellite applications. For automation and communications stakeholders, the key is to evaluate material choices within the full system context and to account for supply-chain access, qualification and production needs early in development. A strong design and research base is valuable, but manufacturing capability and skilled people are also essential to turning RF innovation into deployable systems.