Access Official Technical PDF

Share Summary:LinkedInEmail

Converting a physical measurement into a digital value is a fundamental step in many control and monitoring systems. A sensor produces an analog voltage, and an analog-to-digital converter (ADC) translates that voltage into data a microcontroller can process. For industrial sensor measurement, choosing between a differential ADC and a single-ended ADC affects how the signal is wired, how noise influences the reading, and how the converter’s range is used.

The right approach depends on the sensor output, the electrical environment, and the input range the application needs. Understanding how each method represents a signal helps engineers and system integrators make that choice deliberately.

How a single-ended ADC measures a signal

A single-ended input measures one signal voltage relative to a shared ground. The sensor and microcontroller are expected to use the same ground reference, so a single signal wire carries the measurement to an ADC input.

The ADC maps the input voltage range between ground and its voltage reference, Vref, to digital values. For an n-bit converter, the output typically ranges from 0 to 2n−1. An input at ground corresponds to zero; an input at Vref corresponds to the highest code. Values below ground or above the reference are outside the conversion range and may produce a limited output rather than a useful measurement.

For example, a 12-bit ADC has 4,096 possible codes, from 0 to 4,095. With a 2.0 V reference, a 0.5 V input corresponds to approximately one-quarter of the full-scale range, or a digital value of 1,024.

Where single-ended conversion fits

Single-ended measurement is widely used because it requires only one analog input per sensor and is generally straightforward to connect. It is a practical choice when the sensor and microcontroller share a suitable ground and the signal path is short. Common examples include potentiometers for position or angle, light-intensity sensors, range sensors, and gas or air-quality sensors.

Its main limitation is susceptibility to interference along the signal path and to changes in the shared ground or ADC reference. Longer wiring can increase exposure to noise and differences in ground potential. Depending on the application, signal-conditioning circuitry may be needed, adding design complexity and potentially affecting signal behavior.

How a differential ADC measures a signal

A differential ADC measures the voltage difference between two inputs: a positive input and a negative input. The measurement is the positive input voltage minus the negative input voltage. The individual pin voltages do not have to be negative for the differential result to be negative; the result is negative whenever the negative input is at a higher voltage than the positive input.

Many differential conversions represent signals across a range from −Vref to +Vref. The ADC’s digital output format depends on the device. A signed format may use values from −2n−1 to 2n−1−1. An unsigned format may instead place zero differential voltage near the midpoint of its output range. Engineers should check the device documentation to understand how codes map to input voltage.

For a 12-bit differential ADC with a 2.0 V reference, a −0.5 V differential input is one-quarter of the negative full-scale range. It may be represented as −512 in a signed format, or as 1,536 in an unsigned format with its midpoint at 2,048.

Why use differential signaling?

When the two signal conductors are routed together, interference that affects both similarly can be rejected because the ADC measures their difference. Differential measurement can also reduce the effect of common-mode changes in ground or reference levels. This makes the approach useful where signal paths are longer or electromagnetic and radio-frequency noise is a concern.

It can also make better use of the converter’s range for signals centered around zero or for small signals riding on a DC offset, when the ADC inputs and reference are configured appropriately. Differential ADCs are used with thermocouples, strain gauges, resistor-bridge pressure sensors, and current measurements. A single-ended sensor can also be measured differentially by connecting its ground to the negative input, if the ADC and application permit it.

The trade-offs are additional wiring and the use of two microcontroller inputs per measurement. Differential-capable components may also be less readily available in the lowest-cost ranges, and fewer sensors provide a native differential output. A basic single-ended ADC can sample the two sides of a differential signal separately and subtract the results in software, but because the samples are taken at different times, this approach does not provide the same response to dynamic common-mode noise.

Practical ADC selection and design considerations

Neither input method removes the need to manage noise and voltage limits. Before selecting a converter or setting its reference, consider the full expected input range, including noise and any DC offset.

  • Match the reference to the signal: Choose a Vref that encompasses the expected input range as closely as practical without clipping the signal. A reference that is unnecessarily large uses less of the available ADC resolution.
  • Account for noise: If the input plus noise exceeds the conversion range, the ADC output can saturate and measurement information will be lost. Noise on the signal, ground, or reference can affect the result.
  • Keep analog wiring in mind: Shorter signal paths generally pick up less noise, particularly for single-ended signals. For differential wiring, routing the pair together helps ensure that interference affects both conductors similarly.
  • Check pin-voltage limits: A differential ADC does not necessarily permit each input pin to swing from −Vcc to +Vcc. Confirm that the reference and individual input voltages remain within the device’s specified limits in the selected operating mode.

Where a sensor and microcontroller are electrically isolated, their ground references may differ. Isolation can affect the allowable DC level of the sensor signals, but it does not remove the need to observe the ADC’s input specifications.

Choose the conversion method around the application

A single-ended ADC is often a sensible fit for simple, low-cost measurements with a shared ground and a short, controlled signal path. A differential ADC is worth considering when the sensor provides a differential output, the wiring is exposed to noise, the signal is small relative to its offset, or the measurement requires a range on both sides of zero.

In either case, reliable conversion depends on matching the ADC range to the real signal, including noise, and respecting input voltage limits. Evaluating sensor output, wiring, grounding, and reference selection together gives control-system designers a sound basis for choosing an ADC approach and preserving useful measurement resolution.

Access Official Technical PDF

About The Author