The dsPIC33C digital power starter kit offers engineers a practical way to examine digital control of switching power supplies. Its board combines a dsPIC33CK256MP505 digital signal controller (DSC), an independent synchronous buck converter, an asynchronous boost converter, selectable resistive loads, monitoring and protection circuits, and USB-based programming and communication. Together, these elements provide a compact environment for evaluating control behavior, load response and fault handling.
The kit is a development platform, not a substitute for validating a production power design. Its documented voltage, current, power and thermal limits matter when configuring experiments or connecting external loads.
Two power stages, one digital control platform
The dsPIC33C DSC controls both converter power stages. It generates PWM signals and uses analog-to-digital conversion, comparator functions and feedback signals to support closed-loop operation. In the default configuration, both converters use peak current mode control. The guide notes that average current mode or voltage control can also be implemented with firmware and/or hardware changes to accommodate different sensing signals.
Each converter has its own feedback and power components. The buck stage steps down its input to a programmable output; the boost stage steps the input up. Both are configured by default for a 500 kHz switching frequency, and the output voltage settings are established by firmware.
- Buck converter: Default output is 3.3 V, with a programmable range of 1 V to 3.8 V. The board’s resistive load is limited to 3.3 W; the documented stage rating is up to 7.6 W with an external load.
- Boost converter: Default output is 15 V, with a programmable range of 10 V to 17.8 V. The input must remain below the output voltage. The on-board load is limited to 3 W, while the documented stage rating is up to 6 W with an external load.
For both stages, engineers should check the specified safe operating area as well as the board’s load and thermal limits before increasing output current or power.
Digital power control and system coordination
The control approach illustrates how a DSC can combine fast peripheral functions with firmware-based control. The kit uses a software 2-pole, 2-zero (2P2Z) compensator for closed-loop peak current mode control. ADC feedback supports measurement of converter signals, while PWM peripherals provide switching control. The controller also handles initialization, fault processing and soft start, as outlined in the supplied demonstration software.
A separate PIC24F microcontroller manages the resistive loads and protection-related functions. It exchanges information with the dsPIC33C over UART, including load state, temperature and protection status. This division of work gives users a way to inspect both the real-time converter-control path and the supervisory functions around it.
The board also includes a 2-by-16-character LCD, buttons, LEDs and test points. The display can show system information such as voltage, current, temperature, load settings and converter status. Test points expose signals including PWM drives, switching nodes, feedback, current sensing and protection signals, supporting measurement and debugging with external instruments.
Load steps, monitoring and protection
Selectable on-board resistive loads make it possible to observe how each converter responds to changing demand. The buck load supports 0%, 10%, 50% and 100% settings, up to 1 A. The boost load supports 0%, 15%, 50% and 100%, up to 200 mA. A short press of the corresponding load button advances the setting. Holding the button for two seconds switches between static-load operation and load-step operation.
In load-step mode, the load changes at 100 Hz with a 50% duty cycle. Supported transitions are 10% to 50%, 50% to 100% and 10% to 100% for the buck stage; the boost stage uses 15% to 50%, 50% to 100% and 15% to 100%. These functions allow engineers to examine transient behavior without building a separate programmable load for basic demonstrations.
Protection circuits monitor voltage and current, with documented trip levels of 3 A peak buck input current, 4 V buck output, 1.6 A boost input current and 18 V boost output. When a threshold is crossed, the associated gate drive is disabled and the fault is indicated by an LED. The board also monitors temperature near the resistive loads: a warning is indicated at 65°C, and a higher-temperature fault indication occurs at 75°C. In this condition, loads are switched off until the board cools below 65°C.
Power, connections and practical operating limits
The J1 input accepts a 6 V to 13.8 V DC supply; the kit includes a 9 V supply. Applying power at J1 powers the board’s power stages and auxiliary supplies. USB connection at J6 powers the auxiliary circuitry and provides access to the USB/UART bridge and on-board programmer/debugger, but does not power the buck or boost stages. This distinction is useful when programming or communicating with the board without enabling converter operation.
Thermal management is a key constraint during combined-stage testing. The guide describes two practical operating combinations: running one stage at full on-board load, or running both stages at 50% load. Operating both stages at 100% load produces a combined 6.3 W of on-board dissipation and can overheat the board after a short period. External loads can raise the stages’ output power, but they do not remove the need to respect the board’s operating and thermal constraints.
What engineers can take from the kit
The dsPIC33C digital power starter kit brings converter control, sensing, load testing, communications and protection together in one platform. For system integrators and power engineers, its value lies in making the relationships between firmware, feedback signals, PWM generation and hardware protection visible and testable. Start with the default configurations, use the supplied monitoring features and test points to understand system behavior, and increase loading only within the documented limits. That disciplined approach makes the kit a useful foundation for learning and evaluating digital power control before applying design decisions to a specific application.