Dynamic wireless power transfer (DWPT) offers a different approach to electric vehicle charging: instead of connecting a vehicle to a charger while parked, it transfers energy from roadway equipment to a vehicle as it moves. The approach could address some limitations of stationary charging, but it also introduces demanding requirements for power electronics, coil alignment, electromagnetic safety and infrastructure design.
A prototype study examined a resonant magnetic coupling system for transferring power between a transmitter and a vehicle-mounted receiver. Its findings illustrate the operating principles behind DWPT as well as the practical questions that must be addressed before in-motion charging can be deployed at scale.
How dynamic wireless power transfer works
Wireless power transfer sends electrical energy across an air gap without a physical connector. In an inductive system, an alternating current in a transmitter coil creates a changing magnetic field. When a receiver coil is within range, that field induces a voltage in it. Receiver-side circuitry then converts the electrical output into a form suitable for charging a battery.
DWPT applies this principle while a vehicle is in motion. Transmitter coils are installed along or beneath a roadway, while a receiving coil is fitted to the vehicle. Stationary wireless power transfer uses similar equipment, but charges a vehicle in a fixed location, such as a parking space.
The distinction matters for system design. A moving vehicle continually changes its position relative to the roadway coils. The distance and alignment between transmitter and receiver therefore change during operation, affecting their magnetic coupling and the power that can be transferred.
Why magnetic resonance is used
Magnetic induction is the foundation of both conventional inductive charging and resonant wireless power transfer. In a basic inductive arrangement, current in the primary coil induces current in a nearby secondary coil. Magnetic resonance adds tuned circuits, typically formed from coils and capacitors, so that the transmitter and receiver operate at matching resonant frequencies.
Resonant coupling can support transfer over a greater separation than basic short-range induction, while reducing sensitivity to precise alignment. It is a non-radiative transfer method: energy is coupled through the magnetic field rather than sent as a focused radio-frequency beam. That makes coil spacing, resonant tuning and the properties of the surrounding environment central engineering considerations.
For a two-coil system, power transfer efficiency is associated with operation at the resonant frequency. However, resonance alone does not guarantee maximum output power. The coupling coefficient changes with the distance and relative position of the coils, and the source must be matched appropriately to the system’s input impedance. In a dynamic installation, those conditions can vary as the vehicle moves, making a fixed operating point difficult to maintain.
Efficiency, distance and prototype findings
The study describes a transmitter-and-receiver arrangement using resonant coils and reports a prototype intended to demonstrate dynamic charging. Its discussion also presents theoretical and simulation-based performance results. These should be distinguished from a measured, full-scale road deployment: the reported figures describe the modeled system, not proof of commercial vehicle charging performance.
In the reported analysis, the coils were designed to have matching resonant characteristics. The paper gives a theoretical maximum transfer efficiency of about 96.7% under its stated conditions, and its conclusion reports approximately 95% efficiency at a 25-centimeter coil separation. It also describes a received output of approximately 19.56 watts after rectification in the simulated arrangement. These values are tied to the study’s model and setup; they should not be treated as general specifications for DWPT systems.
The work identifies several linked performance measures that engineers need to evaluate:
- Transfer efficiency: the share of input energy delivered to the receiver.
- Transferred power: the output required for the intended charging application.
- Air gap and operating range: the separation the system can tolerate while maintaining useful transfer.
- Misalignment tolerance: how performance changes as the vehicle shifts relative to the transmitter.
These factors cannot be optimized independently. Increasing the gap or allowing greater misalignment affects coupling, while power levels influence component ratings and thermal and electrical design.
Safety and infrastructure challenges
Wireless charging removes exposed plug contacts, but it does not remove the need for comprehensive safety engineering. Electromagnetic-field exposure must be assessed under normal operation and abnormal conditions. The study notes the possibility of people or animals being near or beneath a vehicle during charging, making exposure limits an important consideration.
Designers must also account for electrical shock, fire and flooding hazards. A road-based system adds civil and operational requirements: transmitter equipment must be integrated into the roadway, and the system must operate as vehicle position and coil coupling change. Matching the receiver characteristics of different vehicle models is another challenge. The paper discusses placing tuning circuitry on the transmitter side as one possible way to avoid adding equipment, weight and cost to every vehicle, while recognizing that appropriate frequency and impedance matching remain necessary.
These issues are especially relevant where stationary charging infrastructure and reliable electricity supply are limited. Local design and manufacturing could be considered as part of a broader EV infrastructure strategy, but the need for safe operation, dependable power and suitable road installation remains.
What engineers should take away
DWPT is not simply a wireless version of a plug-in charger. It is a coupled electromechanical and infrastructure system in which resonance, changing coil geometry, power conversion and safety all interact. The study demonstrates the potential of magnetic resonance for transferring energy across an air gap, while also highlighting why modeled efficiency figures alone are not enough to establish readiness for deployment.
For engineers, integrators and infrastructure planners, the practical priority is to evaluate the complete operating envelope: coil separation, vehicle movement, coupling variation, power requirements, electromagnetic exposure and fault conditions. Dynamic wireless power transfer may become a useful complement to stationary charging, but its value will depend on solving these system-level challenges together.