Access Official Technical PDF

Share Summary:LinkedInEmail

For industrial automation, the promise of 5G includes more than faster mobile broadband. Enhanced Mobile Broadband, ultra-reliable low-latency communications and massive machine-type communications point to networks supporting a wide range of connected devices and applications. Delivering those services requires radio infrastructure that can handle high data rates while fitting the constraints of real deployment sites. E-band mmWave 5G is one proposed part of that infrastructure, particularly for high-capacity backhaul and dense small-cell networks.

The engineering challenge is not simply accessing more spectrum. Millimeter-wave equipment must also be compact, energy-conscious and practical to manufacture at scale. An industry presentation from 2019 argued that integrating radio-frequency filtering and some signal processing into silicon could help address these constraints. Its figures describe the company’s proposed technology and comparisons at that time; they should be understood as stated design targets and estimates, not general performance guarantees.

Why 5G depends on more than new applications

5G architecture is intended to support different service requirements through a service-driven network. The presentation grouped these requirements into three broad categories: eMBB for high-throughput applications, uRLLC for low-latency and high-reliability use cases, and mMTC for large populations of connected devices. Software-defined networking and network functions virtualization were presented as tools for orchestrating services across different access technologies and deployment types.

For automation and operations teams, this matters because a 5G network may need to serve diverse traffic and endpoints rather than a single application profile. But flexible core and cloud-based functions do not remove the physical constraints of the radio access network. Antennas, transceivers, filters, converters and processing hardware still have to fit within site, power and cost limits.

E-band mmWave 5G and the small-cell scaling problem

The presentation identified E-band spectrum, including the 71–76 GHz and 81–86 GHz ranges, as an opportunity for high-capacity links. It discussed applications spanning 5G backhaul and fronthaul, fixed wireless access, mobile access and automotive radar. E-band links can carry substantial bandwidth, but their role depends on how the network is designed and where equipment can be installed.

Small cells bring radio coverage closer to users and devices, but dense deployments multiply the number of sites and associated links. Equipment that is bulky, costly or power-intensive can become a practical barrier when repeated across many locations. The presentation used lamp posts as an example of a potential mounting point, emphasizing a design goal: make high-capacity connectivity equipment small enough to fit existing urban infrastructure.

Massive MIMO adds another scaling challenge. Antenna arrays use multiple elements and signal paths, increasing demands on radio-frequency components and processing. The source characterized conventional integrated microwave assemblies as potentially expensive and difficult to manufacture in volume, with off-chip filters and supporting components adding complexity. These concerns are especially relevant when many compact radio units are needed.

What front-end integration could change

A radio front end typically combines components such as amplifiers, mixers, filters and data converters, with digital processing handling tasks such as signal analysis and beam control. In the approach described, two potential bottlenecks received particular attention:

  • Millimeter-wave bandpass filtering: The presentation identified the lack of suitable on-chip E-band bandpass filters as an integration gap. External filters can add components and assembly steps.
  • Processing wide bandwidths: Converting and digitally processing large bandwidths can require substantial data throughput and processing resources, with implications for latency and power consumption.

The proposed response combined a tunable silicon bandpass filter with analog signal preprocessing. The aim was to perform selected operations before handing data to the system’s digital signal processor, reducing the amount of work required from downstream digital hardware. In particular, the presentation described analog real-time Fourier analysis as a way to identify frequency content without relying on a conventional digital FFT for that task.

It also outlined frequency-controlled beam steering, in which frequency is mapped to beam angle. This is a different beamforming approach from simply adding more digital processing. Whether it suits a particular system depends on the required bandwidth, antenna design and application; the source presented it as a possible way to support more channels or objects with fewer array structures.

Potential trade-offs for network designers

Integration is not valuable in isolation. Network planners and equipment designers must balance link capacity, coverage, power, installation footprint and environmental requirements. The source’s comparisons emphasized that a compact, lower-power link could make shorter-range deployment more practical by supporting denser small-cell placement. That does not mean a shorter-range design replaces longer links in every network. Instead, different link distances may serve different parts of the topology.

For engineers evaluating an integrated mmWave radio, useful questions include:

  • Does the filter provide the required selectivity for the intended band and deployment environment?
  • Which processing functions are performed in analog hardware, and which remain in the DSP?
  • How do power, thermal behavior, size and manufacturing complexity change at the complete-system level?
  • Are link range and capacity appropriate for the backhaul, fronthaul or access role?

The source also discussed automotive radar, where wide bandwidth and rapid signal processing can support detection and resolution goals. This illustrates how filtering and analog preprocessing may be relevant beyond telecommunications, although requirements differ between radar and communications systems.

Practical implications

E-band mmWave 5G can contribute high-capacity links, but widespread use depends on more than spectrum availability. Small-cell and massive MIMO deployments place pressure on radio size, power, cost and manufacturability. Integrating filters into silicon and moving selected signal-processing functions into analog circuitry are potential ways to address those pressures.

For industrial automation decision-makers, the practical takeaway is to assess the complete radio system rather than headline bandwidth alone. The fit of an E-band solution depends on its role in the network, its link budget and its installation constraints, as well as how its front end handles filtering and processing. Compact integration may make dense deployments more feasible, while careful system-level evaluation remains essential before translating proposed component advantages into operational expectations.

Access Official Technical PDF

About The Author