In a mobile robot, a collision is an event that may need attention sooner than the next scheduled sensor update. Edge-triggered interrupts provide a way to detect a change at a bumper input and request immediate processor service. For embedded control engineers, the design challenge is not just recognizing that edge: it is assigning the right priority, keeping interrupt work bounded and coordinating the response with the robot’s normal motion strategy.
A practical collision-detection design separates low-level input handling from higher-level behavior. The interrupt service routine (ISR) identifies the bumper state and initiates an immediate response, while a separate task decides what the robot should do next. This structure supports responsive control without placing the entire navigation strategy inside an ISR.
Why use edge-triggered interrupts for collision detection?
A periodic task checks an input at fixed intervals. If a robot checks its bump sensors every 10 milliseconds, a collision may wait for the next check to be detected. The lab material notes an average latency of 5 milliseconds and a worst-case latency of 10 milliseconds for that period. With a high-priority edge-triggered interrupt, the delay can instead be on the order of 1 microsecond, depending on the system and its implementation.
An edge-triggered input requests service when a digital signal changes state, such as when a bumper switch is pressed. This event-driven approach is useful when a signal represents a condition requiring prompt attention. Similar patterns can apply to external status changes such as a fault or power-failure signal, provided the hardware and software are designed to handle them appropriately.
Set interrupt priority around risk and timing
When several events can occur concurrently, interrupt priority determines which receives service first. A periodic line-sensor measurement may have strict timing requirements, but a collision can represent an immediate hazard to the robot or its surroundings. The collision interrupt should therefore be assigned a higher priority than the periodic measurement in this design.
Priority alone does not make a system reliable. The collision handler must also be short and bounded. Avoid long loops and delay routines in the ISR: lengthy interrupt work can prevent other tasks from running promptly and make system timing harder to predict. The ISR should perform the immediate action needed for the event, capture useful data and leave the longer-term behavior to the high-level control logic.
Separate the bumper driver from robot behavior
A bumper interface function can configure the relevant GPIO pins, internal resistors and edge-triggered interrupts. One way to connect that low-level driver to the robot’s application is through a callback, or function pointer. The application passes its collision-handling function to the driver during initialization; the ISR calls that function when a bumper event occurs.
For example, a high-level handler can stop the motors, store the six-bit bumper reading in a shared variable and set a flag. The main control task or a periodic strategy task can then use that information to choose the next movement. This shared-data pattern provides communication between concurrent parts of the program without putting a complete recovery sequence in the ISR.
A possible robot behavior is to stop after contact, back away, turn and then resume forward movement. The sequence can be represented as timed commands managed by a periodic task. That task can advance through the strategy without relying on long blocking loops, while the edge-triggered interrupt remains responsible for promptly detecting a new collision.
Profile latency and response time
Testing should distinguish between latency and response time. Latency is the interval from the bumper signal changing to the start of ISR service. Response time is the interval from that input change until the required action, such as stopping the motors, has occurred.
An oscilloscope or logic analyzer can make these intervals visible. Observe the bumper input on one channel and toggle an unused output pin at selected points in the ISR or motor-control path. A triple-toggle measurement technique can help identify both the start of service and the completion of the response. The lab specifies that measurements at microsecond scale require a real scope or logic analyzer; a simulator with 100-microsecond resolution is not sufficient for this purpose.
Profiling can also help determine whether one task is preventing another from running. Record useful sensor and actuator information during operation, then inspect the captured data. Measuring how much execution time each thread requires can reveal scheduling or integration problems that are difficult to diagnose by observing the robot’s motion alone.
Integrate and debug incrementally
Collision handling is only one part of a working robot. The bump sensors, motors, periodic measurements, interrupt priorities and high-level strategy must operate together. Develop and test these components separately before combining them, then add functionality incrementally. This makes it easier to identify whether a problem comes from wiring, GPIO configuration, interrupt behavior or the motion-control logic.
- Check the bumper wiring and confirm that pressing a switch pulls its input to 0 volts and releasing it returns the input to 3.3 volts when using the described negative-logic arrangement with internal pull-ups.
- Use a voltmeter, oscilloscope, logic analyzer or debugger to verify that each input changes as expected and that operating one switch does not affect the others.
- Keep MSP432 input voltage limits in mind: the pins are not 5-volt tolerant. The lab calls for powering the line and bumper sensors at 3.3 volts.
- Check port selection before wiring. Ports 1 through 6 can trigger interrupts in this setup, while Port 4 conflicts with the CC3100/CC3120 Wi-Fi module.
Practical implications for real-time robot control
Edge-triggered collision detection gives a robot a faster path from an external event to an immediate control action than periodic polling. The design is most effective when responsibilities are clearly divided: the interrupt detects and reports the event, shared data communicates its details, and a separate task manages the robot’s broader response. Priority choices, bounded ISR execution and measurement with appropriate instruments are all part of making that design predictable.
For engineers integrating embedded sensing and motion control, the key lesson is to treat interrupt handling as one element of a complete real-time system. Verify the electrical interface, profile both latency and response time, and combine tasks in stages. Those practices make collision response easier to assess and provide a sound foundation for more complex robotic behaviors.