Access Official Technical PDF

Share Summary:LinkedInEmail

Electrical chip-board interaction (e-CBI) is a design consideration for semiconductor devices assembled in substrate-less wafer-level packaging. In wafer-level packaging (WLP) and fan-out wafer-level packaging (FOWLP), the silicon die is more directly exposed to mechanical stresses from the printed circuit board (PCB) than it is in a conventional flip-chip chip-scale package. Those stresses can affect transistor characteristics, making e-CBI relevant to package design, board assembly, and electrical performance assessment.

Why substrate-less packaging changes the stress picture

In a conventional flip-chip chip-scale package (FCCSP), the package substrate and other package materials sit between the silicon die and the PCB. These materials provide a buffer between silicon, which has a relatively low coefficient of thermal expansion (CTE), and the board, whose CTE is typically higher. They do not eliminate mechanical stress: thermal expansion mismatch can still stress package structures and the die as the assembly moves between process and operating temperatures.

WLP and FOWLP use fewer packaging materials and omit the package substrate. That can support a smaller package form factor, but it also changes how board-level stress reaches the silicon. With the substrate absent, PCB assembly and materials can become direct contributors to die stress. The resulting electrical effects are described as e-CBI, distinguishing them from mechanical chip-package interaction (mCPI), which is commonly associated with package-related reliability concerns such as solder-joint cracking or low-k dielectric delamination.

How mechanical stress can affect transistor behavior

Silicon transistors respond to mechanical stress through the piezoresistance effect: stress can change channel mobility and, in turn, transistor current. The impact depends on the direction and magnitude of stress relative to the transistor’s current flow. In-plane stress components parallel and perpendicular to that direction, as well as out-of-plane stress, can contribute differently.

For circuit designers, the concern is not simply a visible physical defect. Stress-induced shifts can produce parametric differences in analog circuits or add uncertainty to process, voltage, and temperature (PVT) behavior in digital circuits. These effects may influence performance or yield. Thin dies are particularly relevant because reduced silicon thickness can make the die more susceptible to stress transmitted through the assembled structure.

Stress can be assessed using transistor arrays as electrical sensors and finite element analysis (FEA). Comparing measurements from the same parts at successive assembly stages helps separate assembly-related changes from silicon process variation. FEA can estimate stress components across the die and, with appropriate piezoresistance information, help relate those stresses to transistor current shifts.

A board-level underfill mechanism to watch

One investigated mechanism involves board-level underfill and areas where BGA solder balls have been depopulated. Underfill is used to support board-level reliability, but its interaction with the board, solder balls, and die can also influence stress. Where solder-ball support is absent, underfill shrinkage can pull a thin die toward the PCB, creating local bending.

This bending can produce tensile stress at the active silicon surface in depopulated regions. The largest in-plane stress gradients may occur near the boundaries between areas with and without BGA balls. Consequently, transistor arrays near those transitions can show greater current mismatch after underfill is applied, while arrays in regions with dense ball coverage may show less change.

The effect depends on the package structure. In the studied substrate-less configuration, the board-level underfill could bend the relatively thin silicon die. In an FCCSP, the package’s greater thickness and the position of the die within the package can limit how much board-level bending stress reaches the silicon. This is why assumptions based on one package type should not automatically be carried over to another.

Underfill selection involves competing requirements

Underfill choice can influence e-CBI because material properties affect the stress generated by thermal expansion mismatch. In the reported comparison, an alternative underfill with lower CTE produced less measured and simulated electrical impact than the first material. This supports evaluating underfill as part of the electrical and mechanical design, not only as an assembly material.

However, selecting a material solely to reduce die stress may not satisfy other package requirements. Board-level underfill also serves to protect BGA connections against damage from thermal cycling or drop shock. Those objectives can create trade-offs, so material selection requires consideration of both electrical effects and board-level reliability.

Assess e-CBI across the design and assembly chain

e-CBI is not isolated to one component or engineering discipline. Its outcome can depend on silicon process, circuit design, chip floorplan, package construction, PCB layout, underfill selection, and assembly conditions. A decision made at the board or system level can therefore affect die behavior in a substrate-less package.

A practical assessment can include:

  • Identify sensitive regions: Consider transistor locations relative to die edges, BGA patterns, and transitions between populated and depopulated regions.
  • Compare assembly stages: Measure electrical test structures before board mounting, after mounting, and after underfill application where appropriate.
  • Model the mechanical response: Use FEA to examine stress distribution and compare predicted effects with measured transistor behavior.
  • Evaluate material trade-offs: Consider how underfill properties influence die stress alongside the material’s board-level reliability role.
  • Coordinate across teams: Include chip, package, PCB, and assembly stakeholders early enough to address interactions during development.

Conclusion

Electrical chip-board interaction is a meaningful risk in WLP and FOWLP because removing the package substrate can expose the silicon die to board-induced stress. Local die bending associated with BGA depopulation and board-level underfill can create stress gradients that shift transistor current. For engineering teams, the practical implication is to assess electrical behavior alongside package mechanics, PCB design, and assembly materials. Measurement, modeling, and cross-functional coordination help make these interactions visible before design decisions are fixed.

Access Official Technical PDF

About The Author