Access Official Technical PDF

Share Summary:LinkedInEmail

FRAM can provide industrial automation designs with nonvolatile data storage that does not require a backup battery. The Fujitsu MB85RC256V is a 256-Kbit device organized as 32,768 words by 8 bits, with an I2C interface for communication with a controller. Its combination of high read/write endurance and the absence of a post-write programming wait makes it a memory option to evaluate for systems that update stored data frequently.

As with any component selection, the practical fit depends on more than memory capacity. Engineers should consider the bus topology, write-protection requirements, supply voltage, temperature range, retention expectations and power-up behavior alongside the application’s data-handling needs.

FRAM characteristics relevant to automation systems

The MB85RC256V stores data in nonvolatile memory cells formed using ferroelectric and silicon-gate CMOS processes. Unlike SRAM, it retains data without a data backup battery. The device has a specified read/write endurance of at least 1012 cycles per byte and specified data-retention figures of 10 years at 85 °C, 95 years at 55 °C and more than 200 years at 35 °C.

These figures help frame design decisions, but they should be interpreted in the context of the actual operating conditions. In particular, the data sheet defines endurance in terms of total reading and writing, because FRAM operation uses a destructive-readout mechanism. Retention is also temperature-dependent, so system designers should compare the specified conditions with the expected memory operating environment.

The device operates from a supply voltage of 2.7 V to 5.5 V and is specified for an ambient operating temperature range of −40 °C to +85 °C. Its capacity is 32 KB, arranged as 32,768 8-bit locations. That organization supports byte-level addressing through the device’s memory-address sequence.

I2C interface and system integration

The MB85RC256V operates as an I2C slave. A master initiates communication and supplies the serial clock, while the SDA line carries bidirectional address and data information. The interface supports a maximum clock frequency of 1 MHz. The device uses an open-drain SDA output, so the external bus requires pull-up resistors.

Three hardware address pins, A0, A1 and A2, allow up to eight MB85RC256V devices to share the same I2C bus, provided each has a distinct address-pin combination. The master’s device-address word contains the fixed device type code, the address-pin code and a read/write bit. A device responds only when the received address matches its hardware address configuration.

For control-panel, embedded-controller or other automation designs, this addressability can help organize multiple memory devices on a shared two-wire bus. It also means the system designer must account for bus-level details, including the pull-ups, device addresses and the timing limits for the selected I2C mode.

Write behavior and memory access

Data can be written one byte at a time or in a sequence using the page-write command. During a write, the master sends the device address, the memory address and the data; the slave acknowledges received bytes. The memory address is 15 bits, so the most significant bit of the higher address byte is set to zero. In sequential page writes, the address counter rolls over to 0000H when it reaches the end of the memory space.

A key difference from EEPROM-style write handling is that the MB85RC256V does not require a programming wait after a write or acknowledge polling to check whether an internal write cycle has completed. Data is written after the acknowledge response, and no additional internal programming period is required after the stop condition. This can simplify the controller’s write sequence, although the application must still follow the device’s I2C timing and protocol requirements.

For reads, the device supports current-address, random and sequential access. In sequential reads, the internal address rolls over to 0000H at the end of the memory range and reading continues. The current address immediately after power-on is undefined, so a design that needs a particular location should specify the address through the appropriate access sequence rather than assume a starting address.

Write protection, power and implementation details

The WP pin controls writes to the entire memory array. A high level disables writing, while a low level permits it; reading remains enabled at either level. WP is internally pulled down, meaning an open pin is recognized as low and leaves writing enabled. Designs that require a defined protected state should account for this default in their hardware.

During an access, the data sheet calls for WP and the address pins to remain at a stable high or low level. It also specifies power-up and power-down timing conditions for SDA and SCL. These requirements matter when integrating the memory with a controller that may reset independently, when the memory supply ramps, or when bus activity is interrupted. The data sheet describes a software reset sequence and command retry as recovery options for certain communication failures.

Power consumption is specified at up to 200 μA at a 1 MHz SCL clock, with a typical standby current of 27 μA under the stated conditions. Actual values depend on operating conditions, so these ratings should be used alongside the full electrical characteristics when estimating system power.

Practical selection considerations

Before adopting the MB85RC256V, verify that its capacity, I2C speed and voltage range match the controller and application. Review the endurance definition and temperature-dependent retention values against the data-storage workload and operating profile. Also include SDA pull-ups, device-address pin wiring, WP behavior, power sequencing and recovery handling in the design review.

The practical value of this FRAM is its combination of battery-free data retention, high specified endurance and write operation without an EEPROM-style programming delay. For automation engineers and system integrators, the decision is not simply whether the memory is nonvolatile; it is whether its interface, capacity and operating constraints align with the system’s data integrity and integration requirements.

Access Official Technical PDF

About The Author