Access Official Technical PDF

Share Summary:LinkedInEmail

A modern spectrofluorometer may need to support routine spectral scans as well as specialized research measurements, different sample formats and changing experimental conditions. The FS5 is designed as an integrated platform for photoluminescence spectroscopy, combining steady-state fluorescence with optional lifetime, polarization, near-infrared and other capabilities. For laboratory teams, its practical value lies in how detection, software and sample handling work together across a range of measurement workflows.

How the FS5 spectrofluorometer approaches measurement

The FS5 uses single-photon counting for its measurement modes. In this technique, detected light pulses above a set threshold are counted individually. Because the signal is handled as discrete events, each count has a known statistical basis, and the method is less susceptible to noise interference than other detection approaches described for the instrument.

The optical system is designed to support sensitivity, resolution and acquisition speed. Its air-sealed excitation path is intended to enhance excitation power in the ultraviolet, while temperature-stabilized photomultiplier detectors and selected reflective optical components support signal collection. A small, bright focus at the sample position is also relevant when working with small sample volumes or attachments such as a plate reader, fibre launcher, titrator or sample positioner.

Calibration is another part of producing useful data. Spectral calibration supports wavelength accuracy and repeatability, while photometric calibration helps present spectra without distortion from instrumental throughput. The system uses traceable NIST and BAM standards across its stated wavelength coverage to verify calibration.

Measurement modes for different laboratory questions

The core platform supports excitation, emission and synchronous spectral scans, as well as kinetic measurements and absorption or transmission scans. These modes can address different questions: an excitation or emission scan shows how signal varies with wavelength, while a synchronous scan moves the excitation and emission monochromators together at a fixed offset. Synchronous scans can help distinguish species in dilute mixtures with overlapping absorption and emission, and, with an integrating sphere module, can be used to measure absorption spectra of strongly scattering powders.

A standard transmission detector allows absorption and fluorescence spectra to be measured on the same instrument. It can also monitor transmission changes during fluorescence measurements, which is useful when absorbance may vary in unstable biological or photosensitive systems.

Kinetic scans track changes in fluorescence and absorption over time, from milliseconds to hours. With a titrator or stopped-flow accessory, they can monitor reactions after reactants are mixed. The resulting time-course data can be used to calculate reaction order and rate constants.

Mapping, colour and quantum yield

Excitation-emission maps (EEMs) show signal across a range of excitation and emission wavelengths, creating a spectral fingerprint for complex mixtures. The FS5 uses order-sorting filters to remove higher-order scattered light during map acquisition. Fluoracle software also includes tools for chromaticity analysis using CIE 1931 and CIE 1976 colour coordinates, a measurement need in work involving fluorescent materials and light-emitting devices.

Absolute fluorescence quantum yield measurements for liquids, powders and thin films are available with the integrating sphere module. Samples can be measured with direct or indirect illumination, and the software’s quantum yield wizard supports the calculation workflow.

Software and repeatable workflows

Fluoracle controls instrument options for data acquisition, analysis and presentation. Live signal monitoring displays the signal and instrument status during setup and measurement, helping users optimize parameters before collecting data. The software also supports saved measurement settings, correction functions, spectral maps, kinetic scans and batch acquisition.

Batch files can sequence measurements with delays and loops, and can include temperature or sample changes when the relevant accessories are configured. Analysis tools include wizards for quantum yield, chromaticity, absorption and anisotropy. For time-resolved data, Fluoracle can fit up to four exponential components to fluorescence or phosphorescence decays and provides reconvolution fitting, shift and offset fitting, and fit-quality parameters.

Extending lifetime and wavelength coverage

Options allow the FS5 to be configured for additional measurement requirements. Time-correlated single-photon counting (TCSPC) supports fluorescence lifetime measurements from the picosecond range into the lower microseconds, depending on the pulsed source. Multi-channel scaling (MCS) supports phosphorescence lifetime measurements from the lower microseconds to seconds. The two lifetime approaches can be combined, and software virtual gating can help isolate overlapping fluorescence and phosphorescence components.

Other upgrades include computer-controlled polarization for fluorescence anisotropy and detector or grating options that extend emission coverage into the near-infrared. The available wavelength range depends on the selected configuration; some detector options support photon-counting measurements, while an analogue detector option is specified for steady-state measurements.

Sample handling and temperature control

Sample modules accommodate liquids, solids, powders and thin films. Options include cuvette holders, solid sample stages, an integrating sphere, a microwell plate reader and an optical fibre launcher for connection to third-party accessories. Most modules are designed for plug-and-play installation, and Fluoracle recognizes the module in use and adjusts the interface accordingly.

Temperature-control options cover different sample and workflow needs. These include a thermoelectric cooled holder, a liquid-nitrogen Dewar and a liquid-nitrogen cryostat. Depending on the module, measurements can be made at controlled temperatures or across a temperature range, with spectral and lifetime temperature maps acquired automatically through the software.

Choosing a configuration

For system planners and laboratory managers, configuration should start with the samples and measurements the laboratory needs to support. Consider whether work requires only steady-state spectra or also lifetime analysis, near-infrared detection, polarization, temperature mapping, multiple-sample handling or electroluminescence measurements. The FS5’s modular design allows many options to be combined, while sample modules and accessories can support different formats and experimental setups.

The practical implication is that instrument selection should account for the complete workflow, not just the detector or headline measurement mode. By bringing spectral, kinetic and optional time-resolved techniques together with configurable sample handling and software-controlled acquisition, the FS5 can serve laboratories with varied photoluminescence requirements. Matching its configuration to the intended samples, wavelength coverage and measurement methods is central to making those capabilities useful in routine analysis and research.

Access Official Technical PDF

About The Author