GaN devices on silicon are attracting attention as researchers work to combine the electrical properties of compound semiconductors with silicon-based manufacturing platforms. At the International Electron Devices Meeting (IEDM) 2019, reported developments covered power conversion, radio-frequency (RF) electronics and emerging wireless applications. The common goal was to extend device capability while exploring integration approaches that could support lower-cost manufacturing and broader deployment.
For industrial automation, these developments are relevant to the electronic systems behind power management, communications and high-frequency signal processing. They remain research advances rather than turnkey solutions, but illustrate how device structures and manufacturing processes are evolving to address performance and integration challenges.
Why integrate compound semiconductors with silicon?
Gallium nitride (GaN) and other III–V materials can support power and high-frequency devices, but growing them on silicon with high crystal quality is difficult. That challenge has historically limited the use of GaN-on-silicon devices largely to lower-frequency switching applications, including power conversion and management.
Researchers are pursuing silicon substrates for several reasons. A silicon platform may offer a route to more economical production, while compatibility with established semiconductor fabrication processes can help with integration. The IEDM work examined both devices built directly on silicon and approaches that combine compound-semiconductor devices with silicon circuits or components.
These design objectives do not remove the need to manage material defects, electrical isolation, contacts and device behavior. Instead, the reported work demonstrates different strategies for addressing those engineering constraints.
GaN devices on silicon for power and RF applications
One example came from imec and KU Leuven, which reported GaN power integrated circuits on 200mm silicon-on-insulator (SOI) substrates. SOI provides electrical isolation that can avoid back-gating effects associated with silicon. The circuit included 200V high-electron-mobility transistors (HEMTs), capacitors, Schottky barrier diodes and two-dimensional electron gas resistors.
The researchers also demonstrated a single-stage 48V-to-1V buck converter combining a GaN half-bridge with on-chip driver circuitry. A p-GaN layer enabled enhancement-mode devices. Because an effective p-channel GaN field-effect transistor solution was lacking in this work, resistor-transistor logic was used to implement the required logic function.
In a separate collaboration, researchers presented a CMOS-compatible, gold-free process for aluminium gallium indium nitride devices on 200mm silicon. The HEMTs, metal-insulator-semiconductor HEMTs (MISHEMTs) and MOSFETs were targeted at 20GHz RF operation. The work also reported low transmission loss and contact resistance, a vertical breakdown voltage above 300V, and MISHEMT field-effect mobility exceeding 2000cm2/V-s.
Such RF devices are of interest for applications including radar, satellite links and wireless communications. The move to a 200mm silicon platform and use of standardized CMOS fabrication tools were identified by the researchers as important steps toward adoption in RF and millimetre-wave applications. The results point to integration potential, not proof that every process or device is ready for volume production.
Multi-channel structures target power-device trade-offs
Power transistors must balance on-resistance against the ability to withstand voltage. A lower on-resistance can reduce conduction losses, while adequate breakdown voltage is essential for operation under high electric fields. At IEDM, EPFL and Enkris Semiconductor reported multi-channel AlGaN/GaN MOSHEMTs on silicon designed to improve this trade-off.
The devices used four two-dimensional electron gas channels to reduce on-resistance. Slanted tri-gates, rather than field plates, were used to enhance breakdown performance. The reported specific on-resistance was 0.47Ω-cm2, with a breakdown voltage of 1230V. The team also demonstrated an enhancement-mode version with a threshold voltage of +0.9V under the stated measurement condition.
Multiple channels can provide parallel paths for current, but device design still has to account for electrostatic control and leakage. In the reported structure, barrier-layer thickness and doping were adjusted with the aim of improving control and avoiding punch-through in the off state. These details underline why performance improvements depend on the full device architecture, rather than simply adding conducting channels.
Complementary devices and heterogeneous integration
Complementary circuits use both n-channel and p-channel transistors. In GaN technology, developing effective p-channel devices has been a persistent challenge. Intel reported heterogeneous integration of GaN n-channel devices with silicon p-channel MOSFETs on 300mm high-resistivity silicon. This approach combines different materials and device types on one platform rather than relying on a complete set of GaN complementary transistors.
Other teams explored p-channel III–nitride transistors directly. Cornell University and Intel reported a GaN/AlN heterostructure field-effect transistor that formed a two-dimensional hole gas. A separate collaboration demonstrated GaN pFETs using a self-aligned process and monolithically integrated nFET and pFET devices. These results are significant as demonstrations of possible circuit approaches; the reported p-channel devices still differed in performance and structure from mature silicon CMOS transistors.
Beyond GaN, researchers demonstrated III–V heterojunction bipolar transistors on 300mm silicon using a selective nano-ridge process to trap defects in high-aspect-ratio trenches. Another project integrated III–V tunnel FETs on silicon and reported a subthreshold swing as low as 47mV/decade. These examples show the range of integration methods being investigated for RF and low-power logic.
Other wide-bandgap materials broaden the picture
The meeting also featured work on gallium oxide and silicon carbide. Researchers reported normally-off vertical gallium oxide transistors with breakdown voltages up to 2.66kV and a specific on-resistance of 25.2mΩ-cm2. Separate work transferred thin gallium oxide layers onto silicon and silicon carbide substrates using an ion-cutting method. The transfer approach may help address the material’s comparatively low thermal conductivity by enabling use of a different substrate.
Silicon carbide devices also featured in presentations on a 17kV MOS thyristor combined with an insulated-gate bipolar transistor and on oxygen ion-implant doping in MOSFET channels. The latter work reported reduced specific on-resistance alongside a higher threshold voltage. These studies reinforce that wide-bandgap device development spans several materials, each with its own process and thermal considerations.
Practical implications for automation technology
IEDM 2019 showed research teams exploring how compound semiconductors might be integrated with silicon for power conversion, RF amplification and future communications. For engineers and technical decision-makers, the practical takeaway is to evaluate these technologies by application and maturity rather than treating them as interchangeable alternatives.
Key considerations include voltage and frequency requirements, switching behavior, thermal management, integration with control electronics and the manufacturing process available for a given device. GaN, silicon carbide and gallium oxide each present distinct opportunities and constraints. The reported advances mark progress in device design and platform integration, while further development is needed before research demonstrations can be treated as standard industrial components.