Access Official Technical PDF

Share Summary:LinkedInEmail

GaN-on-silicon power electronics are being developed to combine gallium nitride’s high-voltage and high-frequency potential with silicon’s availability and suitability for large-diameter wafers. For automation engineers and system designers, a central challenge is not simply achieving high device performance: transistors must also switch predictably, limit leakage and integrate effectively with gate-drive and control circuits.

Recent device research explores several ways to address those requirements. The approaches include mechanical stress and passivation to adjust transistor thresholds, magnesium diffusion to create a p-type gate region, ozone-based processing for gate dielectrics, and experimental p-channel devices that could support complementary circuits. The results illustrate both the design options emerging for GaN-on-silicon and the compromises that still need to be managed.

Why GaN-on-silicon matters for power switching

GaN high-electron-mobility transistors (HEMTs), also called heterostructure field-effect transistors, are investigated for high-voltage, high-density, high-frequency switching and RF amplification. Their voltage-handling potential is associated with GaN’s high critical electric field before breakdown. Silicon substrates offer a lower-cost, widely available platform with large wafer diameters, but differences in crystal lattice and thermal expansion between silicon and III-nitride materials can contribute to defects.

Many n-channel GaN HEMTs use a two-dimensional electron gas (2DEG) that forms near the interface between GaN and a barrier such as aluminium gallium nitride (AlGaN). In a conventional structure, this channel can conduct when the gate is at 0 V, producing depletion-mode, or normally-on, behavior. Enhancement-mode, normally-off operation is attractive for power switching because the transistor is off at zero gate bias and can simplify gate-driver design. Achieving that behavior requires controlling the channel beneath the gate without undermining useful on-state performance.

Threshold engineering with stress and passivation

One investigated method uses two silicon nitride (SiNx) layers over an AlGaN/GaN HEMT. The layers serve different purposes: a stressed film changes the 2DEG beneath the gate, while a passivation layer helps limit leakage associated with the AlGaN surface. In the reported devices, the stressed SiNx shifted threshold voltage about 1 V in the positive direction. The devices remained normally-on, but a positive shift is relevant to efforts to develop normally-off variants.

Combining a 200 nm stressed layer with a 14 nm passivation layer preserved on-current at a level comparable to the baseline device. The combined structure reached a maximum on-current of 1 A/mm and a peak transconductance of 280 mS/mm. Its RF cut-off frequency was 36 GHz, similar to the baseline, while the stressed device without passivation reached 20 GHz. Passivation thicker than 7 nm also reduced off-state leakage below the baseline level. The practical lesson is that threshold adjustment must be evaluated alongside current, transconductance, RF behavior and leakage—not as an isolated improvement.

Creating normally-off operation with magnesium diffusion

A separate approach forms a p-type gate region by diffusing magnesium (Mg) into the AlGaN barrier rather than incorporating the dopant during epitaxial growth. The process uses a brief gate-region etch, Mg deposition and rapid thermal annealing. A subsequent air anneal forms a magnesium oxide (MgO) passivation layer.

In the reported comparison, the conventional device had a threshold of –1.5 V, an etched and recessed-gate device measured –0.4 V, and the Mg-diffused gate device reached +1.4 V. That positive threshold represents normally-off operation. However, the full gate-stack device’s drain saturation current was 173 mA/mm, below the 275 mA/mm and 300 mA/mm recorded for the other two structures. Its gate leakage was substantially lower than that of the etched device without Mg diffusion. This highlights a familiar engineering trade-off: changing the gate structure can improve off-state behavior while affecting available current.

Ozone processing for insulated-gate devices

For AlGaN/GaN metal-oxide-semiconductor HFETs, the gate dielectric and its interface with the semiconductor influence leakage, threshold stability and channel behavior. Researchers compared ozone (O3) with water (H2O) as the oxidant in atomic layer deposition of hafnium dioxide (HfO2). In the reported devices, ozone processing reduced threshold hysteresis in MOS structures and was associated with improved interface quality and less charge trapping.

The ozone-based devices also showed a higher maximum saturation drain current than the water-based devices: 340 mA/mm compared with 240 mA/mm. Peak transconductance was 112.6 mS/mm versus 81.38 mS/mm, and gate leakage was more than an order of magnitude lower. Under high-temperature reverse-bias stress, the ozone device’s threshold drift remained below 0.5 V, compared with a +2.5 V shift for the water-based device. In current-collapse recovery testing, the reported time to 90% drain-current recovery was about 0.1 ms with ozone and 20 ms with water. These findings make dielectric process selection an important consideration when assessing dynamic switching behavior, not just static transistor characteristics.

Exploring complementary device structures

Research into p-channel devices addresses a broader circuit-design objective: pairing p-channel transistors with n-channel GaN devices could enable complementary integrated circuits. One demonstrated GaN-on-silicon p-channel MOSFET used Mg-doped p-GaN and an insulated gate. Oxygen plasma treatment enabled enhancement-mode behavior, with a threshold of –1.7 V; without that treatment, the device was depletion-mode, with a threshold of +2.2 V.

The enhancement-mode device had an on-current 67% of the depletion-mode comparison device and an on-resistance of 2.4 kΩ·mm at low drain bias. These results show the promise and the remaining performance gap of p-channel GaN transistors. A separate research direction integrated hydrogen-terminated diamond p-channel transistors on GaN-on-silicon templates. The reported device reached a 109 on/off current ratio and a breakdown voltage of –400 V, while the work also examined diamond’s potential contribution to thermal management. These are research demonstrations, not evidence that a complete complementary power platform is already established.

What engineers should take from the research

For industrial power-conversion and RF applications, the studies point to several evaluation priorities:

  • Confirm switching mode: Check threshold voltage and behavior at zero gate bias, especially where normally-off operation is required.
  • Assess trade-offs together: Compare on-current, on-resistance, transconductance and leakage rather than optimizing one metric in isolation.
  • Consider dynamic behavior: Interface trapping and current collapse can affect performance beyond what static measurements indicate.
  • Track process sensitivity: Etching, passivation, dielectric deposition and thermal treatment all influence device characteristics.
  • Distinguish device research from system readiness: Complementary transistors and integrated structures remain development areas.

GaN-on-silicon offers a platform for pursuing high-voltage and high-frequency devices, but its practical value depends on balancing substrate economics with defect management and careful control of the gate, channel and dielectric interfaces. The reported advances provide engineers with several ways to shape threshold behavior, leakage and dynamic response. For design decisions, the key is to match each device structure and process to the intended operating conditions while treating performance trade-offs as part of the system-level evaluation.

Access Official Technical PDF

About The Author