Access Official Technical PDF

Share Summary:LinkedInEmail

A gate-drive power supply for high-voltage, fast-switching SiC MOSFETs must do more than deliver the required power. It also needs to maintain reinforced isolation, limit common-mode (CM) noise, regulate its output as gate-driver demand changes and respond safely to load faults. A current-transformer-based design offers one way to address these requirements while keeping the isolation structure compact.

The approach, developed for a supply serving multiple gate drivers for 10 kV SiC MOSFETs, combines a single-turn transformer primary with an LCCL-LC resonant converter and a resonant-current bus. Its design choices illustrate how transformer geometry, circuit topology and fault behavior are closely linked in high-voltage power electronics.

Why SiC changes gate-drive power requirements

SiC MOSFETs can support higher blocking voltages and switching speeds than comparable silicon devices. In high-power converters, those characteristics can enable simpler converter arrangements and higher switching frequencies. But fast voltage transitions also create challenges for the isolated gate-drive supply, particularly around insulation and electromagnetic interference (EMI).

The supply’s transformer separates the low-voltage input from the high-voltage switching environment. Two distances matter for insulation: clearance, the shortest path through air between conductors, and creepage, the shortest path along an insulating surface. Meeting a high-voltage creepage requirement with a conventional transformer can demand a large core or circuit assembly, working against compactness.

Fast switching also increases the impact of parasitic capacitance between transformer input and output, identified as CI/O. When a high dv/dt appears across this capacitance, it can drive CM current through the isolation barrier and contribute to EMI. Reducing CI/O is therefore a design objective, not merely a transformer detail.

How a current-transformer approach supports reinforced isolation

The design uses a current-source transformer with a single turn on the primary side. Rather than relying on the transformer core to provide the full creepage path, the high-voltage primary cable provides the insulation distance between the low-voltage and high-voltage interfaces. The cable’s insulation and routing become central to the isolation design, while the core can be selected with less emphasis on providing a long surface path.

A single-turn primary also reduces winding area compared with a transformer that uses multiple primary turns. This helps limit input-output coupling capacitance. The work modeled the capacitance contributions from different winding segments and compared calculated values with measurements across several transformer samples. That modeling approach supports design trade-offs between core dimensions, winding arrangement, magnetic performance and CI/O.

For the optimized transformer examples, the reported input-output capacitance was approximately 1.5 pF, below the stated 2 pF design target. The thesis also describes a 20 kV insulation capability associated with the primary high-voltage cable. These are design-specific results; insulation performance in an installed system still depends on the complete assembly and its implementation.

Resonant conversion and load behavior

Transformer selection affects the converter topology. Because the current-source transformer’s behavior depends on its inductances and operating frequency, the transformer is designed before finalizing the resonant circuit. This lets the converter’s passive components be selected around the transformer rather than treating the transformer as a later, interchangeable component.

The selected LCCL-LC resonant converter uses a resonant-current bus (RCB) on the transformer primary side. The bus is intended to make power transfer less dependent on the number of connected secondary loads. That matters in a multi-channel gate-drive system, where operating conditions may change the demand from individual drivers.

The design also targets zero-voltage switching (ZVS) across the operating range. In ZVS, a switching device turns on when the voltage across it is near zero, which can reduce switching stress and associated losses. The prototype testing described in the work examines ZVS, load independence and output regulation, rather than relying on topology analysis alone.

Fault resilience is part of the power-supply design

A gate-drive supply must account for both open-circuit and short-circuit conditions at its load. The analysis distinguishes the fault response of voltage-source and current-source transformer arrangements. With the current-source configuration, the high-voltage cable contributes leakage inductance, which limits the rise in primary current during a secondary-side short circuit. The design is intended to ride through the fault and recover when the fault is removed.

This does not eliminate the need for system-level protection. Engineers still need to consider how the supply, gate driver and power device behave together during a fault, and confirm that recovery does not create damaging current or voltage transients. Testing the fault and recovery behavior is an important part of validating the complete implementation.

Practical design considerations

The reported application sets out several requirements for a supply operating from a 24 V input and delivering a nominal 28 V output at 10 W per load. Other stated targets include an efficiency above 75%, a volume below 3 cubic inches, input-output capacitance below 2 pF and output variation below 5% from 20% to full load. These requirements show why the design must balance electrical performance with packaging and isolation needs.

  • Start with the isolation path: Define how creepage and clearance will be achieved before fixing the transformer and board layout.
  • Control parasitic capacitance: Treat winding geometry and cable placement as key variables in CM-noise mitigation.
  • Design transformer and converter together: Transformer inductances and operating frequency shape the resonant-stage design.
  • Validate changing loads and faults: Confirm regulation, ZVS behavior, load sharing and recovery under the conditions relevant to the application.

Conclusion

A current-transformer-based gate-drive power supply can help address the competing demands of high-voltage isolation, low CM coupling, compact construction and fault response in SiC converter systems. Its single-turn primary and cable-based insulation path change how the transformer supports creepage, while the LCCL-LC resonant stage and resonant-current bus address power transfer and changing load conditions. For engineers and system integrators, the central lesson is to treat isolation, parasitic capacitance, topology and protection as connected design problems—and to verify their interaction through prototype testing.

Access Official Technical PDF

About The Author