Access Official Technical PDF

Share Summary:LinkedInEmail

For engineers developing semiconductor materials and optoelectronic devices, controlling a nanostructure’s dimensions is only part of the design challenge. Ge quantum dot passivation can also influence where photogenerated carriers recombine—and therefore which wavelengths the material emits. Experiments on germanium (Ge) quantum dots formed by solid-state dewetting show that oxide-related defects have a dual role: they contribute to blue-green visible luminescence and can quench infrared emission from the dots.

The result is a useful materials-engineering lesson: fabrication sequence and interface condition can matter as much as particle size when interpreting optical behavior. In this case, adding a thin amorphous-silicon passivation layer before silicon dioxide encapsulation enabled infrared photoluminescence associated with quantum-confined excitons.

How dewetting forms germanium quantum dots

The process begins with a thin amorphous Ge film deposited on a silicon dioxide layer over a silicon substrate. During thermal annealing, the film dewets: instead of remaining continuous, it reorganizes into separated, three-dimensional Ge particles. The reported process used in-situ annealing at 550°C for 30 minutes to form randomly distributed dots.

Atomic force microscopy showed that dot diameter depended on the initial Ge film thickness. In the reported samples, dewetting a 1 nm film produced dots with an average diameter of about 7 nm, while a 2 nm film produced dots averaging about 14 nm. Dot density varied inversely with the square of the initial film thickness. These relationships indicate that controlling deposited Ge thickness provides a way to tune the resulting dot size and density, although the reported values describe the specific fabrication conditions used.

Transmission electron microscopy and Raman spectroscopy provided evidence that the dots crystallized. Raman measurements showed the Ge–Ge vibrational mode, while the absence of detected Si–Ge modes indicated no measurable interdiffusion between the Ge dots and the amorphous-silicon cap within the instrument’s detection limit.

Why oxide interfaces affect visible emission

Ge quantum-dot samples showed a blue-green photoluminescence band centered around 520 nm. This emission appeared in both passivated and unpassivated samples and did not shift with the two dot sizes examined. That size independence distinguishes it from the infrared response associated with the Ge crystal.

The visible band was attributed to luminescent defect centers associated with GeOx or SiOx, including defects at interfaces between the dots and surrounding oxide. A proposed pathway is that excitons generated in a Ge dot diffuse to oxide-related states and recombine there, producing visible light. This can divert electron–hole pairs from recombination within the Ge crystal.

The distinction matters when evaluating photoluminescence data. Visible emission alone does not establish that quantum confinement in the Ge dots is responsible for the light. The emission’s wavelength dependence on dot size, together with its response to surface treatment, helps separate defect-related luminescence from emission originating within the nanocrystal.

Ge quantum dot passivation and infrared photoluminescence

To limit GeOx formation at the dot surface, some samples received an in-situ 1 nm amorphous-silicon cap after dewetting. All samples were then encapsulated with 50 nm of silicon dioxide. The passivation was not complete: one side of each dot remained in contact with the underlying SiO2. Even so, the optical measurements showed a clear difference between the sample groups.

  • Without silicon passivation: infrared emission was not measured for the Ge dots in the SiO2 matrix, regardless of dot diameter.
  • With silicon passivation: infrared photoluminescence appeared and shifted with dot size.

The passivated dots with average diameters of 7 and 14 nm produced broad infrared peaks centered at 0.85 and 0.82 eV, respectively. Both energies are higher than the 0.74 eV bandgap of bulk Ge. Because Raman measurements indicated that the dots were fully relaxed, the reported peak shifts from the bulk value were attributed to quantum-confinement effects. The emission width was linked to the distribution of dot sizes.

In practical terms, the comparison supports a connection between surface defects and carrier loss. Passivation reduced the loss of photogenerated electron–hole pairs associated with defect-related states at the dot surface or in surrounding oxides. More carriers could then recombine radiatively inside the Ge dots, producing infrared emission. The findings do not show that oxide-related visible emission disappears after passivation; rather, visible luminescence remained while infrared emission became observable in the passivated samples.

Implications for materials and process development

For teams evaluating Ge nanostructures for optoelectronic applications, the work highlights several factors to consider together:

  • Starting-film thickness influences the resulting dot dimensions and density.
  • Thermal processing drives the transformation from a continuous amorphous film to crystalline, three-dimensional dots.
  • Surface and interface chemistry affects whether carriers recombine through oxide-related states or within the Ge nanocrystals.
  • Optical interpretation should distinguish size-independent visible emission from size-dependent infrared emission.

These observations are specific to the studied Ge/SiO2 structures and process conditions; they should not be treated as universal performance guarantees. They do, however, show why fabrication records and interface characterization are essential when comparing optical results across samples.

Conclusion

Solid-state dewetting offers a route to self-assembled Ge quantum dots whose size can be adjusted through the initial amorphous Ge thickness. But dot geometry alone does not determine the observed emission. Oxide-related defects can produce blue-green luminescence while also diverting carriers from infrared recombination in the Ge crystal. In the reported structures, an amorphous-silicon passivation layer enabled size-dependent infrared photoluminescence despite persistent visible emission. For materials development, the practical implication is clear: control and characterize both nanostructure dimensions and surface interfaces when optimizing Ge-based optical behavior.

Access Official Technical PDF

About The Author