Access Official Technical PDF

Share Summary:LinkedInEmail

As photovoltaic generation becomes part of a facility’s electrical supply, engineers must consider more than the amount of energy a system produces. Grid-connected PV harmonics can affect current waveforms and contribute to power-quality concerns in distribution networks. The scale and location of those effects depend on inverter operation, the electrical load and how power flows at the point of common coupling (PCC).

Understanding these interactions helps system designers and plant operators distinguish inverter-related effects from distortion generated by connected equipment. It also provides a more useful basis for monitoring power quality than assessing the PV system in isolation.

Why harmonics matter in grid-connected PV systems

A PV array produces direct current (DC). A grid-connected inverter converts that energy to alternating current (AC) so it can supply local loads and exchange power with the utility network. Because the inverter uses switching electronics, its operation can introduce harmonic components into current waveforms. Nonlinear loads can also draw distorted current, making the combined behavior at the PCC important.

Harmonics are components of a periodic voltage or current waveform at multiples of the fundamental frequency. When present, they change the shape of the waveform from an ideal sinusoid. Total harmonic distortion (THD) is commonly used to express the contribution of harmonic components relative to the fundamental component. Voltage and current distortion are related but distinct measurements; a system may show relatively low voltage harmonic distortion while current harmonics are more noticeable.

Significant harmonic distortion can contribute to equipment and system problems, including increased losses, overheating, resonance, overcurrent, overvoltage or protection issues. These are potential power-system concerns, not outcomes that should be assumed for every PV installation. Their relevance depends on the electrical network and the equipment connected to it.

How the PV system, grid and load interact

Harmonic measurements at the PCC reflect the interaction of multiple sources and paths. When the PV inverter is not supplying power, loads draw energy from the grid. Any harmonics produced by nonlinear loads can flow back toward the network. When the PV system begins exporting or supplying power, the current distribution changes, but the load’s own harmonic behavior does not necessarily disappear.

The reported analysis compares conditions with and without PV generation and considers measurements on the grid, PV and load sides. Its central finding is that load type and inverter output both matter. In the examined conditions, load harmonics were more influential on grid harmonics than PV-system harmonics, while harmonics from the PV system had little effect on the load side. This describes the study’s observations, rather than a universal rule for all network configurations.

The results also indicate that current harmonics can change as PV output increases, while measured voltage harmonics may remain comparatively low. The amount and pattern of current distortion depend in part on the power supplied and the connected load. A nonlinear load, such as an LED lamp with its driver, may contribute distortion of its own. Consequently, an increase in measured harmonics should not automatically be attributed to the inverter alone.

Load characteristics shape power-quality measurements

The experimental setup used a PV simulator, an on-grid inverter, a grid connection and several load types. These included an incandescent load, a ballast, a combination of incandescent and ballast loads, an LED lamp and a motor. Voltage and current waveforms were recorded with an oscilloscope, while a power-quality analyzer captured electrical parameters and harmonic measurements.

This range of loads is useful because equipment does not draw current in the same way. A load’s electrical characteristics influence the harmonic content observed at the connection point. Comparing different operating conditions can help identify whether distortion is associated primarily with a particular load, PV inverter operation or their interaction with the network.

For industrial facilities, this supports a practical measurement approach:

  • Establish a baseline: Record power-quality conditions when the PV system is not supplying the connection point, where operationally feasible.
  • Compare operating states: Repeat measurements with PV generation active, noting inverter output and the loads in service.
  • Measure at relevant locations: Consider the PCC as well as PV and load connection points to understand how harmonic currents are distributed.
  • Review load composition: Account for nonlinear equipment that may contribute distortion independently of the PV system.

Implications for design and operations

Power-quality assessment should include the inverter, the distribution network and the facility’s loads. Checking only the PV inverter may miss distortion contributed by downstream equipment; measuring only at a general supply point may make it harder to identify where the distortion originates. Measurements across operating states and connection points provide context for interpreting the results.

Inverter design, filtering and control can influence harmonic behavior, but the supplied analysis does not establish a single mitigation measure for every installation. Any response should follow from measured conditions and the applicable project requirements. Engineers should also consider reactive-power and voltage behavior at the PCC as part of the wider grid-integration assessment, rather than treating current harmonics as the only power-quality concern.

Conclusion

Grid-connected PV harmonics are shaped by the interaction between inverter output, load characteristics and the distribution network. The analysis highlights that load-generated harmonics can have a greater influence on grid harmonics than PV-system harmonics under the conditions examined, and that current distortion may vary even when voltage distortion remains low. For plant teams and system integrators, the practical lesson is to measure the system in more than one operating state and at meaningful connection points. This makes it easier to separate the effects of PV generation from those of facility loads and to make informed power-quality decisions.

Access Official Technical PDF

About The Author