Access Official Technical PDF

Share Summary:LinkedInEmail

Grid-interfaced renewable energy systems must coordinate power generation with the electrical conditions at the point of common coupling. This matters especially when a distribution network supplies nonlinear loads, which can draw distorted current and consume reactive power. A photovoltaic (PV) system connected through a controlled inverter can contribute to power quality as well as deliver active power. In the approach described here, the grid-interfacing inverter also operates as a shunt active power filter.

Why power quality needs attention

Nonlinear loads, including equipment that uses power-electronic converters, do not draw current in a smooth sinusoidal waveform. Their distorted current can introduce harmonics into the network, while reactive power demand can reduce power factor. Unbalanced loads may also contribute to power quality concerns in distribution systems.

Renewable generation introduces another control requirement: its output varies with conditions such as solar irradiance and temperature. When a PV source is connected to a grid through power electronics, the interface must manage that generation while responding to the needs of the load and utility connection. The system therefore needs a control strategy that addresses both power transfer and current quality.

Grid-interfaced renewable energy as an active filter

The proposed arrangement connects the PV source to the DC link of a grid-interfacing inverter. Rather than connecting the PV source directly at the common coupling point, the inverter provides the interface between the source, load and grid. In this configuration, it can transfer PV active power while injecting compensating current to address disturbances associated with the load.

For harmonic compensation, the inverter supplies current that counteracts the harmonic components drawn by the load. The aim is for the resulting grid current to be closer to a sinusoidal waveform. The inverter can also supply reactive current to meet the load’s reactive power demand, supporting an improved power factor. These functions are combined with the transfer of active power from the PV system.

This multifunctional role is significant for system design: the inverter is not treated solely as a renewable-generation interface. Its control is also used to provide shunt active filtering, so the power-conditioning function is implemented through the grid-interfacing converter in the proposed system.

How the control strategy works

The control algorithm establishes reference currents for the inverter and uses a hysteresis current controller to generate its switching pulses. The DC-link voltage is central to active-power transfer. A measured DC-link voltage is compared with its reference, and a proportional-integral (PI) controller processes the error to produce a current component associated with active power.

A second control path compares the measured voltage amplitude with a reference voltage. Its PI controller produces a quadrature current component associated with reactive power. Unit vectors derived from the source-voltage information are used to form the reference current components. Combining the active and quadrature components gives the reference currents for the phases.

The controller then compares the measured source current with the reference. When the current departs from the reference beyond the hysteresis band, the controller changes the inverter switching state to drive the current back toward the target. This feedback process allows the inverter current to track the reference and produce the intended compensation.

PV modeling and simulation results

The PV module is represented using a single-diode model with series and parallel resistances. Its electrical output depends on input conditions, particularly irradiance and temperature. Changes in these conditions affect the module’s current, voltage and power, so the model accounts for their influence when representing the PV source.

The system was modeled and simulated in MATLAB/Simulink with a nonlinear load. In the reported comparison, the source current without filtering was distorted, and its total harmonic distortion (THD) was about 29.9%. With the inverter operating as a shunt active power filter, the reported source-current THD fell to 2.02%. The simulated results also show reactive power from the grid being compensated and a unity power factor.

These figures describe the simulation conditions and results reported for this system; they should not be taken as a guaranteed outcome for other installations. Actual performance depends on the system design, control implementation and operating conditions.

Practical considerations for engineers and integrators

For plant teams evaluating renewable integration, the key point is that power quality can be considered as part of inverter control rather than as a separate function alone. A design review should examine how the controller identifies current references, maintains the DC-link voltage and responds to changing load conditions. It should also assess the required current tracking behavior and the interaction between PV power transfer and compensation demands.

  • Assess the load: Identify nonlinear and unbalanced load conditions that may affect current quality.
  • Define control objectives: Clarify the requirements for active-power transfer, harmonic compensation and reactive-power support.
  • Validate operating cases: Use suitable modeling and testing to check controller behavior across relevant source and load conditions.
  • Measure at the grid interface: Evaluate source-current waveform, THD and power factor at the point of connection.

Conclusion

A PV-connected grid-interfacing inverter can serve both as a renewable energy interface and as a shunt active power filter. With PI-based reference generation and hysteresis current control, the simulated system reduces source-current harmonics, compensates reactive power and supports unity power factor while transferring PV active power. For automation and power-system decision-makers, the practical implication is to treat inverter control and power quality as connected design concerns and validate performance against the installation’s specific loads and operating conditions.

Access Official Technical PDF

About The Author