In a ground plane UTBB SOI MOSFET, the doped region beneath the buried oxide can influence both substrate potential and transistor behavior. For engineers evaluating fully depleted silicon-on-insulator devices, that influence matters because it can alter analog figures of merit, including saturation transconductance, output conductance, intrinsic voltage gain and Early voltage. The direction and size of the change depend on the device structure and operating conditions; adding a ground plane does not improve every parameter.
How the ground plane affects UTBB SOI devices
Ultra-Thin Body and Buried Oxide (UTBB) SOI devices use a thin silicon channel above a buried oxide layer. The front gate controls the channel from above, while the substrate can act as a back gate. With a thin body and buried oxide, electrical coupling between the front and back interfaces can be significant. Changes in back-gate voltage may therefore affect substrate potential and the transistor’s electrical characteristics.
A ground plane is formed by implanting dopant beneath the buried oxide. In the devices discussed here, boron implantation increased the substrate concentration in the ground-plane region. This approach is intended to reduce the influence of the substrate and the depletion region at the buried-oxide/substrate interface. However, the ground plane also changes how drain electric fields penetrate the device, creating a trade-off relevant to analog performance.
Ground plane UTBB SOI MOSFET results depend on device design
The comparison covered nMOSFETs with 70 nm and 1 µm channel lengths, a 6 nm or 14 nm silicon film, and either SiO2 or a high-κ gate dielectric. The devices were evaluated with different back-gate biases. Together, these variables determine whether front-to-back gate coupling or drain-field penetration is the stronger influence.
Long-channel devices with a thin SiO2-gated body
For the 1 µm channel device with a 6 nm silicon film and SiO2 gate dielectric, the ground plane increased saturation transconductance under some tested conditions. The explanation is strong coupling between the front and back interfaces, sometimes described as supercoupling. In the depletion regime at the buried-oxide/substrate interface, the ground plane reduced the substrate potential drop compared with the device without a ground plane. This difference was associated with higher saturation transconductance in the ground-plane device.
This result is not a general improvement across analog metrics. For this device configuration, the devices without a ground plane generally showed more favorable output conductance, intrinsic voltage gain and Early voltage. The measured behavior reflects the balance between gate coupling and drain-field effects, rather than a simple benefit from adding the implant.
Shorter channels and thicker silicon films
In short-channel devices, drain electric-field penetration becomes more influential. The study found that the ground plane was associated with greater drain-field penetration in the relevant channel region. This tended to degrade analog performance, including transconductance, compared with devices without a ground plane. A similar pattern applied to the 14 nm silicon-film devices: the thicker body reduced the relative importance of front-to-back gate coupling, leaving drain-field penetration as a more significant factor.
Across the evaluated devices, shorter channel lengths also showed the expected analog trade-offs: saturation transconductance, intrinsic voltage gain and Early voltage decreased as channel length fell, while output conductance increased. This channel-length effect appeared for each of the technology configurations examined.
Back-gate bias changes the comparison
The effect of ground-plane implantation also varied with back-gate bias. The analysis considered biases from -3 V to 1 V, with the selected range informed by the operating conditions of the buried-oxide/substrate interface. When that interface was in depletion, the substrate potential drop—and the difference between devices with and without a ground plane—could be substantial. In accumulation or inversion, the substrate effect was smaller in the reported cases.
For long-channel devices with SiO2, devices without a ground plane generally provided better analog results as back-gate bias varied, with the notable exception of saturation transconductance in the thin-body configuration. This makes bias conditions an important part of device evaluation: measurements at a single back-gate voltage may not represent behavior across the intended operating range.
High-κ gate dielectric reduces ground-plane sensitivity
The 6 nm silicon-film devices using a high-κ gate stack showed less variation between ground-plane and no-ground-plane conditions than the SiO2 configurations. The study reported relatively small percentage differences in the measured parameters for this technology. A ground plane could still affect individual results, but its overall influence was less pronounced in the tested high-κ devices.
Practical implications for analog design
Ground-plane selection should be assessed against the specific analog requirements and transistor structure, rather than treated as a universal performance improvement. When comparing UTBB SOI nMOSFET options, engineers and device teams should consider:
- Channel length: Short-channel behavior is more affected by drain-field penetration.
- Silicon-film thickness: A thinner body can strengthen front-to-back gate coupling.
- Gate dielectric: The tested high-κ devices were less sensitive to the ground plane than the SiO2 devices.
- Back-gate bias: The bias can change substrate potential and the relative performance of devices with and without a ground plane.
- Target analog metric: A condition that benefits transconductance may not also benefit output conductance, voltage gain or Early voltage.
For circuit and process decisions, the practical conclusion is to evaluate the complete set of analog figures of merit under representative bias conditions. Ground-plane implantation can help one parameter in a particular long-channel, thin-body configuration while degrading or barely changing others. Its value depends on the interaction among body thickness, dielectric stack, channel length and back-gate operating point.