Access Official Technical PDF

Share Summary:LinkedInEmail

Harmonic analysis of nonlinear loads is an important part of managing power quality in facilities that use power electronic equipment. Variable frequency drives (VFDs), uninterruptible power supplies (UPSs), battery chargers, compact fluorescent lamps and other electronic devices can draw current in a way that does not follow the supply voltage as a simple sinusoidal waveform. The resulting harmonic currents can contribute to voltage distortion and affect connected equipment.

For automation engineers, plant managers and system integrators, the practical task is not just to identify that harmonics are present. It is to measure their magnitude, understand how indicators relate to operating conditions, and determine whether mitigation should be considered at the relevant point in the electrical system.

How nonlinear loads produce harmonics

A linear load has a comparatively constant relationship between applied voltage and current. With a sinusoidal supply, it draws a current waveform that is also sinusoidal. A nonlinear load has an impedance that changes during the AC cycle, so its current waveform departs from a pure sine wave. Power electronic switching is one common reason for this behavior.

A distorted periodic waveform can be represented as a fundamental-frequency component plus harmonic components. Each harmonic order is an integer multiple of the fundamental frequency: on a 50 Hz system, for example, the second harmonic is 100 Hz and the third is 150 Hz. Components that are not integer multiples are not classified as harmonics.

Nonlinear loads are found in both domestic and industrial environments. Examples include UPSs, switched-mode power supplies, battery chargers, electronic lighting, solid-state fan regulators, rotary converters and VFDs. The mix of equipment and its loading conditions influence the harmonic current drawn by a facility.

Why power quality harmonics matter

Harmonic currents can increase heating in electrical equipment, including transformers and generators, and contribute to additional conductor losses. Harmonics also interact with the wider electrical system: the resulting voltage distortion may affect equipment connected to the same supply.

Potential effects include interference with communications, data corruption, flicker or changes in lighting intensity, and malfunction of control equipment. Motors carrying excessive harmonic current may also experience lower power factor and reduced efficiency. These effects are reasons to investigate measured conditions rather than assume that every nonlinear load presents the same level of risk.

Key indicators for harmonic analysis of nonlinear loads

Total harmonic distortion

Total harmonic distortion (THD) expresses the combined root-mean-square value of harmonic components relative to the fundamental component. Voltage THD and current THD are calculated separately, using the corresponding voltage or current components. A pure sinusoidal waveform containing only the fundamental has a THD of zero.

THD is widely used to describe waveform distortion, particularly voltage distortion. However, current THD needs context. A small current can have a high THD percentage while its absolute harmonic current remains low. This can occur, for example, when an adjustable-speed drive is operating at light load. A percentage alone therefore may not show how significant the harmonic current is to the system.

Total demand distortion

Total demand distortion (TDD) addresses this limitation by relating harmonic current to the maximum demand load current at the point of common coupling (PCC), rather than to the fundamental current in the measurement sample. The demand-current basis is important when interpreting results and applying IEEE 519 guidance. It should be established appropriately for the assessment; it is not interchangeable with a snapshot current value.

Power factor and transformer K-factor

Under sinusoidal conditions, power factor can be described using the phase angle between voltage and current. When waveforms contain harmonics, that angle alone does not represent the full relationship between real and apparent power. True power factor accounts for the effects of waveform distortion as well as the fundamental-frequency phase relationship.

Transformer K-factor is another indicator used when harmonic currents are present. It weights harmonic current components according to their order and is used in assessing transformer heating and potential derating needs. It can inform equipment selection and installation planning where nonlinear loads are expected.

A measurement-led assessment process

A useful harmonic study links measurements to the facility’s load profile and the applicable power quality criteria. A practical sequence is to:

  1. Identify likely sources. Review the connected equipment, including drives, UPSs, converters, chargers and electronic lighting.
  2. Measure electrical conditions. Use a power quality or harmonic analyzer to record voltage and current harmonic components under relevant loading conditions.
  3. Choose appropriate indicators. Review voltage and current THD, TDD where applicable, power factor and, when relevant, transformer K-factor.
  4. Assess the measurement location and basis. Document the PCC and the demand-current basis used so that comparisons with applicable limits are meaningful.
  5. Compare results with relevant requirements. Evaluate measured conditions against the standards and contractual limits that apply to the installation.
  6. Select mitigation based on the findings. Consider options such as line reactors, isolation transformers, phase-shifting transformers, or active and passive harmonic filters.

Measurements at different loading conditions can help distinguish a high relative distortion percentage from a substantial harmonic current contribution. The assessment should also account for the system location where measurements are taken and the purpose of the comparison.

Turning analysis into practical decisions

Harmonic analysis provides a basis for deciding whether power quality concerns warrant further investigation or mitigation. No single indicator captures every aspect: THD describes distortion relative to the fundamental, TDD provides a demand-based reference for current distortion, and power factor and K-factor offer additional perspectives relevant to system operation and equipment planning.

For industrial facilities, the practical implication is to pair analyzer measurements with a clear understanding of the load mix, operating conditions and PCC. Compare results with applicable requirements before selecting a mitigation measure. This measured approach helps engineers and operations teams address harmonic concerns with solutions suited to the electrical system rather than relying on assumptions about individual devices.

Access Official Technical PDF

About The Author