Access Official Technical PDF

Share Summary:LinkedInEmail

Harmonic distortion occurs when voltage or current waveforms in an AC power system depart from a sinusoidal shape. For industrial facilities, understanding harmonic distortion is important because the effects can extend beyond the equipment that creates it, influencing neutral conductors, transformers, motors and other parts of the electrical distribution network.

What causes harmonic distortion?

In an ideal supply, voltage is sinusoidal, and a linear load draws current that follows the shape of the applied voltage. Nonlinear loads behave differently: their current waveform does not match the voltage waveform. Electronic switching and rectifying devices can draw current for only part of each power-frequency cycle, producing a distorted waveform.

Common sources include power converters, uninterruptible power supplies (UPS), electronic power supplies, fluorescent lighting and ballasts, fan speed controls, dimmers and arc devices. Harmonic currents may originate within a facility or arrive through the utility supply. Other customers connected to the same part of the grid can also contribute to supply distortion.

A distorted periodic waveform can be represented as a combination of sinusoidal components. The fundamental is the system-frequency component; harmonics occur at integer multiples of that frequency. For example, the fifth harmonic of a 50 Hz supply is 250 Hz. Fourier analysis separates a measured waveform into its frequency components, helping engineers identify harmonic orders and their magnitudes.

Why harmonic order matters

Harmonic components do not all produce the same effects. In many systems, harmonic amplitudes tend to decrease as harmonic order rises, although the actual spectrum depends on the loads present. Equipment limits therefore distinguish between harmonic orders rather than treating all distortion alike.

Many nonlinear loads produce waveforms that are symmetrical around their average centreline. Such waveforms contain odd harmonics, while even harmonics are absent or small. This is one reason limits for even harmonics may be less restrictive in some equipment classifications. Asymmetrical waveforms, however, can contain even harmonics too, so their presence should be assessed rather than assumed away.

Triplen harmonics and neutral conductors

Triplen harmonics are harmonic orders that are multiples of three, including the third and ninth. They require particular attention in three-phase, four-wire systems. In a balanced system, the fundamental currents in the three phases are separated by 120 degrees. For triplen components, the phase displacement becomes a whole number of cycles, bringing those components into phase with one another.

As a result, triplen harmonic currents can add in the neutral conductor instead of cancelling. Other harmonic sequences may cancel in the neutral under balanced conditions, but the triplen components do not. Significant neutral current can cause conductor heating; if conductors are not suitably sized, overheating can create a serious safety risk. Triplen harmonics can also contribute to transformer problems, making their control relevant to facility distribution design and operation.

Negative-sequence harmonics and motor performance

In three-phase systems, harmonic components can be grouped by their phase sequence. Positive-sequence harmonics rotate in the same sequence as the fundamental. Negative-sequence harmonics rotate in the opposite sequence, while zero-sequence components are in phase across the three phases. The fifth harmonic is negative sequence; the seventh is positive sequence, and triplen components are zero sequence.

Sequence matters for AC motors because the rotating magnetic field produced by three-phase power influences rotor torque. Positive-sequence components support the fundamental rotation, while negative-sequence components act against it. Excess negative-sequence harmonic content can therefore degrade motor performance and increase heating. Higher-order harmonics are generally attenuated more by system inductance and magnetic core losses, so the fifth is often a key harmonic to examine.

Other effects on electrical distribution

Harmonic currents and voltages can affect several types of equipment. Potential consequences described for power systems include:

  • Neutral and transformer heating: Harmonic current increases losses and can raise operating temperatures, affecting equipment life and rating.
  • Capacitor stress: Power factor correction capacitors can be overstressed in the presence of harmonics.
  • Protective-device operation: Harmonic conditions can contribute to nuisance tripping of residual current circuit breakers.
  • Motor losses: Harmonic voltages can increase motor losses and heating, reducing available output and potentially shortening service life.
  • Power-line carrier interference: Harmonics close to carrier-signal frequencies can disrupt systems such as synchronized clocks, building-management controls and ripple-control relays. Filtering may not be a simple remedy because it can also remove the carrier signal.

Equipment classification and harmonic current limits

Equipment emission limits are organized by equipment class. The classification approach described in the IEC framework considers factors such as how many units are likely to operate, how long they run, whether they operate simultaneously, their power consumption and their likely harmonic spectrum, including phase.

The classes distinguish, for example, balanced three-phase equipment and many household appliances (Class A), portable tools and certain arc-welding equipment (Class B), lighting equipment (Class C), and specified personal computers, monitors and television receivers (Class D). The source classification identifies Class D equipment as having a power level from 75 W up to and including 600 W.

Class C limits illustrate how permitted harmonic current can vary by order. In the cited limits, the second harmonic is limited to 2% of fundamental input current, the third to 30 minus the circuit power factor, the fifth to 10%, the seventh to 7%, and the ninth to 5%. Odd harmonics from the eleventh through the thirty-ninth are limited to 3%. Applicable requirements depend on the relevant standard and equipment category, so engineers should confirm the limits that govern the installation and equipment under assessment.

Practical implications for facility teams

Harmonic management starts with understanding which loads create distortion and where that distortion appears in the electrical network. Measuring and analyzing waveforms can reveal the magnitudes and orders present; Fourier analysis provides a way to decompose a waveform into those components. Equipment classification and applicable emission limits then help frame compliance considerations.

For plant engineers and system integrators, the practical priority is to consider more than the source device. Assess how harmonic currents interact with shared conductors and equipment, paying particular attention to neutral loading, transformer heating, motor performance, capacitors and sensitive power-line carrier systems. Addressing harmonic distortion as a distribution-system issue helps teams evaluate both equipment emissions and their potential effects across the facility.

Access Official Technical PDF

About The Author