Access Official Technical PDF

Share Summary:LinkedInEmail

High-power InP photonic integrated circuits (PICs) bring lasers, modulators and semiconductor optical amplifiers (SOAs) together on a single chip. This integration can reduce system footprint and packaging complexity, while supporting optical transmitters for applications where output power and compactness matter, including free-space communications and microwave photonics. A key engineering challenge is that the components needed for an efficient transmitter do not all perform best with the same optical waveguide design.

Two transmitter approaches illustrate how material processing and waveguide structure can address these competing requirements. One uses offset quantum wells (OQW); the other uses quantum well intermixing (QWI) with an epitaxial structure designed to support lower optical confinement in power-amplifying sections.

Why high-power InP photonic integrated circuits are challenging

InP is a mature platform for integrating active devices such as lasers, SOAs and modulators with passive components including waveguides, filters and couplers. Combining these elements monolithically can reduce the need for discrete optical components. But each device has different design priorities.

  • Lasers benefit from strong optical confinement in the active region to achieve modal gain.
  • Modulators need material and waveguide properties suited to changing the optical signal electrically, with insertion loss also a consideration.
  • Output SOAs benefit from lower optical confinement, which can increase the power they deliver before gain saturation.

In a conventional narrow active waveguide, a relatively large share of the optical field overlaps the gain material. That helps provide gain, but the concentrated photon density can deplete carriers as optical power rises, reducing amplification. Lowering the confinement factor spreads the optical mode over a larger effective area and can increase an SOA’s saturation output power. The design task is to achieve that lower confinement without compromising optical transitions to the laser, modulator and passive waveguides.

Two integration strategies for optical transmitters

Offset quantum wells: a simpler integration route

The OQW approach selectively removes quantum wells from regions where optical gain is not required, followed by a shared cladding regrowth. Its relatively simple process supports integration of multiple functions, but the available material regions constrain how independently each component can be optimized. In particular, the SOA may share epitaxial layers with the laser, limiting the opportunity to create a low-confinement structure specifically for high output power.

The demonstrated OQW transmitter integrated a widely tunable sampled-grating distributed Bragg reflector (SGDBR) laser, a high-speed SOA, a Mach–Zehnder modulator and a two-section output booster SOA. It tuned from 1521 to 1565 nm while maintaining more than 45 dB side-mode suppression. The measured off-chip output power was 14.5 dBm, and the transmitter operated at data rates up to 7 Gbps.

Quantum well intermixing: tuning bandgaps after growth

QWI changes the bandgap of quantum wells after the semiconductor layers have been grown. In the described process, ion implantation and annealing cause changes that shift the bandgap in selected regions. This provides a way to create different material properties for gain, modulation and passive waveguiding while limiting refractive-index discontinuities at component interfaces.

The QWI transmitter used a distributed Bragg reflector laser, a high-speed electroabsorption modulator (EAM) and output amplification. Its measured off-chip power was approximately 19.5 dBm, with NRZ on-off keying demonstrated at up to 20 Gbps. The results show how an alternative integration process and a more suitable epitaxial structure can improve both output power and modulation speed relative to the OQW demonstration.

Waveguide design connects integration with power

The QWI platform was paired with an epitaxial structure that includes a thick lower waveguide layer. This layer can support a larger optical mode and lower confinement in an SOA section. In the reported design analysis, modifying the ridge geometry reduced the calculated confinement factor to 0.41% and increased modal area by a factor of 3.3 compared with the reference structure.

A transition between higher- and lower-confinement sections remains essential: the laser and modulator need a guided mode compatible with their functions, while the output amplifier benefits from a more expanded mode. The proposed transmitter architecture therefore includes intermediate gain and waveguide sections to connect these regimes. The integrated ultralow-confinement output SOA was presented as a platform direction; its expected performance should not be confused with the measured results of the earlier transmitter.

This distinction matters when evaluating an integrated photonic design. A strong result from a laser, modulator or standalone amplifier does not by itself establish the performance of the complete transmitter. Interfaces, mode transitions, optical loss and the electrical drive of each section all contribute to system-level operation.

Practical implications for system designers

For engineers assessing integrated optical transmitters, the work highlights several useful design considerations:

  • Match the integration process to device needs. OQW offers a comparatively straightforward route, while QWI enables more selective bandgap engineering.
  • Design the output stage around saturation power. Waveguide geometry and optical confinement influence how an SOA behaves as output power increases.
  • Account for interfaces. Mode mismatch between active and passive regions can undermine the benefits of otherwise well-optimized components.
  • Assess power and data rate together. Transmitter evaluation should consider optical output, modulation performance and tuning requirements as a system, rather than as isolated device metrics.

These considerations are relevant wherever an optical subsystem must combine compact integration with demanding transmitter performance. For industrial automation teams working with optical links or photonic systems, they also illustrate why material platform, component architecture and packaging choices need to be considered together.

Conclusion

High-power InP PIC transmitters depend on more than adding an amplifier to a laser. Their performance is shaped by how material regions are engineered, how strongly the optical mode overlaps the gain region, and how efficiently different waveguide sections connect. The OQW and QWI demonstrations provide distinct routes to monolithic integration, while the lower-confinement design points toward further increases in SOA saturation power. For system designers, the practical lesson is to optimize the transmitter as an integrated whole, balancing output power, modulation, tuning and optical transitions.

Access Official Technical PDF

About The Author