PCBA reliability depends on more than component selection and circuit design. In humid operating environments, moisture can interact with ionic residues, board materials and applied voltage to create leakage paths and accelerate corrosion. These effects can cause intermittent faults as well as permanent failures, making it important for engineers to understand how climate and contamination act together.
A central factor is the thin water layer that can form on a printed circuit board assembly (PCBA). When that layer dissolves surface contaminants, it can become electrically conductive and provide a pathway for electrochemical reactions. The resulting risk depends on local conditions—including humidity, temperature, contamination type and concentration, board layout, and electrical bias.
How humidity turns contamination into a reliability risk
Moisture interacts with electronics in several ways. It can be absorbed into the PCB laminate, adsorbed onto a surface, or taken up by hygroscopic residues. Absorbed water may affect material properties and contribute to internal degradation. At the board surface, moisture and contamination are especially relevant to surface insulation resistance (SIR), which describes how well the surface prevents unintended current flow.
Many ionic contaminants attract water. As relative humidity rises, they adsorb increasing amounts of moisture. Once humidity reaches a contaminant’s deliquescence relative humidity (RH), the solid residue can dissolve into a liquid solution. That solution contains mobile ions, so it can conduct electricity between adjacent conductors and lower SIR.
The threshold is not the same for every residue. Sodium chloride and solder-flux residues have different moisture responses, and mixtures of contaminants can deliquesce at lower humidity than individual substances. Consequently, a board’s response cannot be inferred from ambient humidity alone; the type and combination of residues also matter.
Key failure mechanisms on printed circuit assemblies
Leakage current and reduced SIR
When a conductive water film bridges conductors, leakage current can flow across the board surface. The current may interfere with circuit operation, contributing to erroneous signals or intermittent functionality. As dissolved contamination increases the solution’s ionic conductivity, the risk of SIR reduction and associated leakage rises.
Local conditions matter. The water layer’s thickness and composition are influenced by humidity, temperature, board surface characteristics and the amount of contamination. Temperature changes can also create local humidity differences; if a board surface cools below conditions that support moisture retention, condensation may occur even when the surrounding enclosure conditions are not uniform.
Electrochemical migration and dendrite formation
With an electrical bias applied, metal can dissolve at one conductor and move through the moisture layer as ions. Under suitable conditions, metal can deposit at the opposing conductor, forming a conductive growth known as a dendrite. This process, called electrochemical migration (ECM), can eventually create a short circuit.
ECM is shaped by more than the presence of water. Contaminant concentration, voltage, spacing and local pH near the electrodes all influence the process. Electrolysis can create acidic conditions near the positive electrode and alkaline conditions near the negative electrode. For tin, these local chemical conditions affect the stability and movement of metal ions and the formation of dendrites.
Voltage waveform is also relevant. Investigations of tin migration under pulsed voltage found that reducing the voltage duty cycle prolonged time to failure under the tested conditions. During the unpowered intervals, precipitation of tin hydroxides was more favourable, and fewer metal ions were reduced at the cathode. This does not remove the need to assess the specific circuit and environmental conditions, but it demonstrates that bias characteristics can influence migration.
Other corrosion-related concerns
Humidity and contamination can contribute to corrosion beyond surface leakage and ECM. Relevant mechanisms include galvanic corrosion, creep corrosion and corrosion associated with gaseous environments. Moisture absorption into laminate materials can also affect internal reliability, including through mechanisms such as conductive anodic filament formation. In microelectronics, iodine exposure was found to make aluminium metallization and aluminium-rich Au-Al intermetallic phases particularly susceptible to corrosion.
What engineers should consider in reliability assessment
There is no single corrective measure that addresses every climatic reliability risk. Assessment should consider how manufacturing residues, board materials, circuit geometry and operating conditions combine in the intended environment. Useful questions include:
- What ionic residues may remain from manufacturing or enter during service, transport or storage?
- At what humidity can those residues absorb enough water to form a conductive solution?
- Could temperature gradients or enclosure conditions produce local moisture or condensation at the PCBA surface?
- Which conductor pairs are exposed to bias, and how do their spacing and materials affect the potential for leakage or ECM?
- Are board cleanliness, conformal coating, circuit design or enclosure choices appropriate to the expected climate?
These considerations support early identification of sensitive board regions and help guide design, process control and protection decisions. Electrical testing can assess SIR and leakage behaviour under controlled environmental conditions. Corrosion observation and analysis can provide complementary evidence about where degradation begins and how it progresses. A tin-ion indicator gel method described in the research can help visualize tin corrosion and the movement of tin ions across a PCBA surface, supporting failure analysis and corrosion profiling.
Prediction remains challenging because outdoor conditions vary over daily and seasonal cycles, while the temperature and humidity at the board surface may differ from the surrounding air. Enclosure design and device operation also affect local conditions. For that reason, meaningful evaluation should connect environmental testing with the actual board layout, materials, contamination and bias conditions rather than treating humidity as an isolated variable.
Conclusion: treat climate, contamination and bias as a system
Humidity-related electronics failures arise through interactions: hygroscopic residues take up water, dissolved ions make surface films conductive, and applied voltage can drive leakage, corrosion or electrochemical migration. The practical implication for PCBA reliability is that engineers should evaluate contamination, humidity, temperature, materials and electrical bias together. Combining design and manufacturing controls with relevant environmental and electrical testing can help identify vulnerable areas earlier and inform appropriate protection and failure-analysis strategies.