Access Official Technical PDF

Share Summary:LinkedInEmail

For electric scooters, a hybrid energy storage system (HESS) can pair a battery’s energy capacity with a supercapacitor’s ability to handle rapid power demands. When combined with wireless power transfer (WPT), the result is an integrated approach to charging and energy management. A demonstrated 48-V scooter system brings these elements together, using the HESS to regulate incoming wireless power and distribute energy between storage devices.

The design addresses two practical challenges: batteries can be stressed by repeated high-current charge and discharge, while scooter batteries are often limited in capacity by vehicle size. The system’s three operating modes direct energy according to the battery and supercapacitor voltage conditions, with a further charging mode intended to ease battery polarization.

Why combine a battery and supercapacitor?

Batteries and supercapacitors store and deliver energy differently. A battery relies on electrochemical reactions and provides the energy storage needed for vehicle operation. A supercapacitor stores energy through an electric field and can respond to high-power demands. Its energy density is lower than a battery’s, so it is not a direct replacement.

In a scooter, this division of work can help manage short-lived demands such as acceleration. The supercapacitor can contribute high current during a transient, while the battery supplies energy for normal operation. The intended benefit is to reduce the need for the battery to handle every large charge or discharge current on its own. The supercapacitor can also support charging and energy distribution within the HESS.

This arrangement depends on coordinated power management. The HESS is not simply two storage devices connected together: its control strategy determines how energy from the charger is routed and when each storage element is used.

Wireless charging with double-sided LCC compensation

The scooter’s WPT unit uses a loosely coupled transmitter and receiver coil, with a double-sided LCC compensation network. LCC compensation uses inductors and capacitors on both sides of the transfer link to establish resonant operation. In the reported design, the coils were separated by a 15-cm air gap, and the system operated at 85 kHz, following the frequency standard identified in the study as SAE J2954.

A key design consideration is how power responds to changes in coupling between the coils. The paper notes that, with LCC compensation, delivered power is proportional to the coupling coefficient. This relationship is useful when considering practical coil alignment: reduced coupling reduces transferred power, rather than producing the power increase that the authors identify as a concern with a series-series arrangement.

After the receiver coil, a rectifier converts the received AC power to DC. The HESS then manages that input using its converters and switching controls. In the reported test, the wireless stage achieved 90.362% efficiency from the DC source to the DC output after the rectifier at an output power of 631.7 W. The overall efficiency from the DC source to the battery and supercapacitor was reported as 86.4% at 596 W. These are results for the tested system, not universal performance figures for WPT chargers.

How the three-mode energy management strategy works

The control strategy uses the battery and supercapacitor voltage conditions to select among rapid, normal and smart charging. Each mode gives the incoming power a different path.

Rapid charging: prioritize the supercapacitor

When the supercapacitor voltage is below the battery voltage, the system enters rapid charging. In this mode, the input energy is directed to the supercapacitor. The aim is to build up its stored energy quickly, making it available to support subsequent power demands and the system’s charging sequence.

Normal charging: share the input

Once the supercapacitor reaches the specified voltage condition, the system switches to normal charging. Power is supplied to both storage devices, with the current distribution shaped by their electrical potential and impedance. As the supercapacitor voltage rises, its charging current decreases; a greater share of current can then flow to the battery. The relationship is expressed as the WPT current equaling the sum of the battery and supercapacitor currents.

Smart charging: introduce a brief negative-current interval

In smart charging, the system uses a buck-converter interval to charge the battery and a boost-converter interval to transfer energy from the battery-side inductor to the supercapacitor. The reported control schedule assigns 80% of the processing cycle to buck charging and the remaining 20% to boost charging. During that shorter interval, the battery current briefly becomes negative as energy is transferred toward the supercapacitor.

The authors describe this as a depolarization-related mechanism. A brief negative-current period is intended to help alleviate concentration polarization and avoid excessive battery exploitation. The test bench confirmed that triangular and negative battery current could be produced. However, the reported experiments do not quantify a battery-life extension, so the mechanism should be understood as a design objective rather than a measured service-life result.

Implications for system integrators

For engineers evaluating a scooter charging architecture, the example shows why wireless power transfer and energy storage control should be designed as a system. Coil compensation, rectification, DC conversion and battery-supercapacitor management all affect how input power reaches the storage elements. The HESS also needs control logic that accounts for the different roles and voltage conditions of its two storage devices.

  • Match storage roles to load demands: use the battery for energy storage and normal operation, with the supercapacitor supporting high-power transients.
  • Define mode transitions clearly: the reported strategy bases transitions on battery and supercapacitor voltage conditions.
  • Evaluate the complete power path: distinguish wireless-stage efficiency from overall efficiency through the HESS.
  • Validate battery-related outcomes: demonstrating negative-current operation does not, by itself, establish a quantified improvement in battery life.

Conclusion

A battery-supercapacitor HESS can coordinate energy storage and transient power support in an electric scooter, while WPT removes the need for a wired charging connection. In the demonstrated design, double-sided LCC compensation transfers power across a 15-cm gap, and a three-mode strategy manages charging across the battery and supercapacitor. For industrial automation and power electronics teams assessing similar systems, the practical lesson is to treat wireless transfer, converter design and energy management as connected parts of one architecture—and to validate claimed battery benefits separately from demonstrated electrical operation.

Access Official Technical PDF

About The Author