Access Official Technical PDF

Share Summary:LinkedInEmail

Industrial data acquisition systems help engineers investigate how electrical and electromechanical equipment behaves over time. The right instrument must match the signals under test, the number of channels, the required sampling rate and the duration of a measurement. For applications ranging from short-lived transients to long-running durability tests, modular recorders, synchronized acquisition units and mixed-signal oscilloscopes offer distinct approaches.

Understanding those differences is important before specifying a measurement setup. A system suited to a few fast electrical signals may not be the best fit for combining sensor outputs and vehicle-network data, or for recording many channels across multiple instruments.

Start with the measurement challenge

Define what the test needs to capture before comparing instrument specifications. Consider whether signals are electrical, physical or digital; whether events are repetitive or intermittent; and whether measurements must run for seconds, hours or longer. Channel count and synchronization needs also shape the choice.

For example, investigating an electromechanical system may require simultaneous measurement of voltage and current alongside temperature, vibration, strain or rotational information. In vehicle development, engineers may also need to relate physical signals to data on CAN, LIN or SENT buses. Capturing these sources together can help reveal how system behavior relates to control or sensor data.

Industrial data acquisition systems for mixed signals

A ScopeCorder combines waveform recording and analysis with modular input conditioning. Depending on the main unit and installed modules, it can measure voltage, temperature, strain, acceleration, frequency and logic signals. Some configurations also support CAN, LIN and SENT monitoring. This modular approach is useful when a test combines different signal types rather than relying on a single uniform input.

The DL850E and DL850EV can accommodate up to eight plug-in modules, with a maximum of 128 analog channels in specified configurations. Sampling rate, bandwidth and other measurement characteristics depend on the module used. The DL850EV adds support for particular vehicle-network monitoring modules, while its optional DC power input can support operation from an external DC source within the stated input range.

Record length is another consideration. The ScopeCorder’s memory options allow longer recordings or more captured data at a given sampling rate, while optional hard-disk recording supports continuous data storage. The source specification describes recording at 100 kS/s on 16 channels for 10 hours, subject to the configuration and storage arrangement. For long-duration tests, check the complete instrument and storage configuration rather than treating memory capacity alone as a guarantee of recording time.

When synchronized acquisition matters

The SL1000 high-speed data acquisition unit is designed for applications that need multiple channels or synchronized instruments. A single unit supports up to 16 input channels; up to eight units can be synchronized for a maximum of 128 channels. With compatible modules, the system supports sampling rates up to 100 MS/s on all channels.

Data recorded across synchronized units is linked through a common file, allowing the recordings to be processed together. This can help organize measurements when a test setup spans multiple acquisition units. The SL1000 supports PC-based acquisition and data transfer over USB 2.0 or, with the relevant option, Gigabit Ethernet. An optional internal hard drive also allows recording without a connected PC.

Sampling rate and channel count affect how much data can be recorded. The unit’s available recording time varies with the number of modules, measurement mode and sampling rate. Engineers should therefore check the instrument’s recording limits against the full test plan, especially when collecting many channels at high rates.

Oscilloscopes for waveform and logic analysis

Mixed-signal oscilloscopes are suited to examining electrical waveforms alongside digital logic. The DLM2000 series offers configurations with two or four analog channels; on four-channel models, an analog input can be switched for logic input. The DLM4000 series provides up to eight analog channels and logic inputs, depending on configuration.

Oscilloscope features such as trigger functions and history memory are useful when events are intermittent. The DLM2000 series can retain up to 50,000 previously captured waveforms, which can be reviewed to investigate unusual signals. Depending on model and options, the DLM series also supports serial-bus analysis, including protocols such as UART, I2C, SPI, CAN, LIN and SENT. These capabilities can help engineers examine relationships between analog behavior and digital communications.

Unlike a modular recorder configured for diverse sensor inputs or long-duration recording, an oscilloscope is often selected for detailed waveform observation and triggering. Available bandwidth, sample rate, memory depth, channel configuration and analysis options vary by model, so compare the specific configuration with the application’s requirements.

Build the system around the test

A practical selection process is to document the test’s essential requirements:

  • Signal types: Identify voltage, current, temperature, strain, acceleration, frequency, logic and bus signals that must be measured.
  • Channel count and timing: Establish how many inputs are needed and whether measurements across instruments must be synchronized.
  • Time and sampling: Determine how long data must be recorded and the sampling rate needed to capture events of interest.
  • Analysis and storage: Check trigger, waveform review, bus analysis, data transfer and recording options against the planned workflow.
  • Input compatibility: Confirm that the selected modules, probes and accessories suit the signals and the instrument configuration.

Conclusion

Industrial data acquisition systems are not interchangeable simply because they record waveforms. A modular ScopeCorder can bring varied physical and electrical measurements together; synchronized SL1000 units address higher channel counts across linked instruments; and DLM mixed-signal oscilloscopes support waveform, logic and bus analysis. Matching the instrument architecture to signal types, recording duration, channel count and analysis needs gives engineering teams a clearer basis for reliable testing.

Access Official Technical PDF

About The Author