Access Official Technical PDF

Share Summary:LinkedInEmail

Power quality issues can interrupt industrial processes even when electricity remains available. A voltage dip, transient or distorted waveform may be enough to affect a programmable controller, adjustable speed drive or other sensitive equipment. For automation engineers and plant leaders, understanding these disturbances is an important step toward diagnosing equipment problems and protecting process continuity.

In practical terms, power quality describes how closely the electrical supply matches a clean, steady sinusoidal waveform at the expected voltage and frequency. Modern facilities rely on electronic controls and power converters, while also operating motors and other substantial loads. The resulting mix of load types and switching activity can contribute to disturbances in the supply.

Why power quality matters in industrial facilities

Industrial automation depends on electrical equipment operating within its expected conditions. A disturbance may cause a control device to malfunction, interrupt a production sequence or contribute to equipment heating and failure. Power quality problems can also increase energy losses and interfere with communication systems. In severe cases, a disturbance can bring part or all of a plant operation to a halt.

Not every disturbance has the same cause or effect. Some are brief changes in voltage magnitude; others involve waveform distortion, frequency deviation or a sustained loss of supply. Separating these categories helps teams describe an event accurately and investigate the equipment and system conditions involved.

Voltage changes and interruptions

Sags, swells and short-duration variations

A voltage sag is a temporary reduction in root-mean-square (RMS) voltage. The source describes a sag as a reduction to between 10% and 90% of the original voltage, typically lasting less than one minute. Large motor starts are a common cause because motors draw higher current while accelerating. Sudden load changes, transformer energization and faults can also produce sags. Sensitive process controllers and adjustable speed drives may respond poorly to these reductions.

A voltage swell is a temporary rise in RMS voltage, described in the source as reaching 110% to 180% of nominal voltage for less than one minute. Swells are associated with system faults and can occur on non-faulted phases, depending on the system and grounding arrangement. Both sags and swells are short-duration variations; their effects depend on the disturbance and the equipment connected to the affected supply.

Interruptions and longer-term voltage variation

An interruption occurs when voltage falls below 10% of nominal for a limited period. Its duration can depend on how quickly protective equipment clears a fault and whether the supply is restored automatically. Sustained interruptions last more than one minute and may require human intervention to repair the system and restore service.

Long-duration voltage variations also include overvoltage and undervoltage. These conditions last more than one minute and may result from load changes, switching operations, transformer tap settings or inadequate voltage regulation. An overloaded circuit or the switching on of a load can contribute to undervoltage, while switching off heavy loads or energizing capacitor banks can contribute to overvoltage.

Other disturbances affecting automation equipment

Fluctuations, flicker and unbalance

Voltage fluctuations are changes in supply magnitude. Rapid, repeated changes associated with varying load current can produce flicker, perceived as instability in the brightness of a light source. Arc-related loads are identified as one source of voltage fluctuation.

Voltage unbalance occurs in a three-phase system when phase-voltage magnitudes or the angles between them are unequal. A blown fuse in one phase of a three-phase bank is one possible cause. Unbalance can affect three-phase loads, so it is relevant when investigating motor or other equipment behavior.

Frequency variation and transients

Frequency is linked to generator speed and the balance between generation and load. Small deviations may occur during normal operation, while larger shifts beyond established limits can be associated with major power-system events, such as a large load being disconnected or a significant generation source going offline.

Transients are brief, unwanted changes in voltage or current during a transition between operating conditions. Impulsive transients are unidirectional and are commonly associated with lightning. Oscillatory transients alternate in polarity and can arise from events such as capacitor switching. Transients can contribute to motor heating, insulation degradation, increased losses and wear on protective-device contacts.

Waveform distortion, harmonics and power factor

Waveform distortion is a departure from a pure power-frequency sine wave. Harmonics are frequency components at integer multiples of the fundamental frequency. Nonlinear loads, including power-electronic equipment, can generate them. As harmonic levels rise, connected equipment may experience heating, failure or electromagnetic interference with communication circuits.

Other forms of distortion include DC offset, inter-harmonics, notching and electrical noise. Inter-harmonics occur at frequencies that are not integer multiples of the fundamental and can be associated with equipment such as frequency converters and induction furnaces. Notching is a periodic voltage disturbance during current commutation in power-electronic devices. Noise consists of higher-frequency signals superimposed on the waveform and may interfere with microcomputers or programmable controllers, particularly when grounding is unsuitable.

Nonlinear loads can also distort voltage and current waveforms and contribute to a lower power factor. A poor power factor is associated in the source with higher load current, poorer voltage regulation, increased copper losses and greater equipment or conductor requirements.

Practical implications for plant teams

When a control system, drive or motor behaves unexpectedly, consider the supply as well as the device itself. A useful investigation starts by describing the event: Did voltage fall, rise or disappear? Was the change brief or sustained? Was the waveform distorted, or was the issue linked to frequency or phase balance? These distinctions help narrow the possible causes without assuming that every malfunction has the same origin.

The source identifies several broad ways to address power quality concerns: update or restore technology, select equipment with lower sensitivity to disturbances, and use interfacing devices. The appropriate response depends on the disturbance, the equipment affected and the installation. Clear characterization of the event is therefore an important basis for deciding what action is suitable.

Conclusion

Power quality issues range from voltage sags and interruptions to harmonics, transients and frequency variation. Their practical impact can include control malfunctions, equipment stress, wasted energy and production disruption. For industrial facilities, recognizing the type and duration of a disturbance helps teams assess equipment vulnerability and make informed decisions about technology, equipment selection and power-system interfaces.

Access Official Technical PDF

About The Author