Access Official Technical PDF

Share Summary:LinkedInEmail

Integrated narrow-linewidth lasers can support applications where optical frequency and phase noise affect system performance, including coherent communications, RF photonics, and optical sensing. A demonstrated silicon/III-V platform combines a semiconductor gain section with a long, low-loss silicon Bragg reflector. One version produced more than 37 mW of on-chip power with a Lorentzian linewidth of about 1.1 kHz; a ring-assisted design reached a linewidth of 500 Hz, with lower output power.

The results illustrate a central design challenge for photonic integration: reducing laser linewidth without sacrificing output power or stable single-mode operation. The approach depends on the laser cavity, the reflector, and the waveguide platform working together.

How integrated narrow-linewidth lasers use an extended cavity

The extended distributed Bragg reflector (E-DBR) laser uses a III-V gain section bonded to a silicon photonic circuit. The gain material supplies optical amplification, while a long Bragg grating in the silicon waveguide forms the front mirror and much of the laser cavity. A tunable reflector at the back of the cavity completes the design.

A long cavity can reduce linewidth, while a narrow reflector response helps select and stabilize the lasing mode. In this device, the Bragg grating is 15 mm long and deliberately weak, with a designed grating strength low enough to produce a narrow reflection band. The weakest measured grating had a 3 dB bandwidth of 2.9 GHz and peak reflectivity of roughly 40%.

Grating strength involves a practical compromise. Increasing it raises reflectivity, but also broadens the grating response. Making it weaker can narrow the response, but the reflector must still provide sufficient feedback after propagation losses are taken into account. The long grating and low-loss waveguide are therefore complementary parts of the linewidth-reduction strategy.

Why ultralow-loss silicon waveguides matter

Propagation loss is especially important when light travels through a long reflector. Loss within the grating reduces the returned optical power and increases mirror loss, undermining the benefits of an extended cavity. The reported silicon platform achieved single-mode TE waveguide propagation loss below 0.16 dB/cm across the C and L bands. Its shallow-rib geometry is etched 56 nm into a 500 nm silicon layer.

The platform was developed to support both long, weak gratings and integration with the III-V gain section. The shared silicon thickness allows the silicon waveguide and III-V epitaxial stack to form a hybrid optical mode in the gain region. This arrangement combines different materials for different functions on one chip rather than requiring a separately assembled external cavity.

For very low grating strength, conventional sidewall or surface perturbations can become difficult to fabricate reliably. The design instead uses periodically etched holes beside the waveguide. Adjusting the distance between the holes and the waveguide controls the coupling strength, providing a way to implement a weak grating using lithographically defined features.

What the ring-assisted design changes

The ring-assisted E-DBR (RAE-DBR) adds a high-Q ring resonator to the laser cavity. Near resonance, the ring increases the effective cavity length and sharpens the filtering response. Its measured resonance had a full width at half maximum of 0.35 GHz, narrower than the Bragg grating response. The ring must be tuned to the Bragg wavelength so that it does not add unnecessary loss.

This design achieved a measured Lorentzian linewidth of 500 Hz. However, its maximum reported on-chip output power was 4.8 mW, compared with more than 37 mW for the E-DBR. The difference was attributed to higher cavity and output-mirror losses in the ring-assisted configuration. The ring therefore improves linewidth in this implementation, but does not deliver the same output-power level.

Output power, mode control, and operating stability

The E-DBR reached more than 37 mW on chip, with a threshold current of 50 mA. Its side-mode suppression ratio exceeded 55 dB. When coupled into a fiber, the maximum reported power was 8.3 mW; the measured coupling loss from the angled facet to the lensed fiber was 6.5 dB.

As drive current increases, heating can shift the lasing mode away from the grating peak. The result may be a drop in output power followed by a hop to another longitudinal mode. The device includes a phase-control section that can be thermally tuned to align the lasing mode with the reflector peak. In the reported measurements, active phase tuning supported a cleaner, more continuous power response across a larger portion of the current range.

Operation near a mode hop can also involve competing modes and, in some conditions, multimode, chaotic, or self-pulsing behavior. An integrated monitor photodiode provides a signal for tracking the tunable reflector and observing changes that can indicate proximity to a mode-hop region. This makes phase adjustment relevant not only to spectral alignment but also to practical operating stability.

Implications for photonic system design

Low-noise lasers are valuable in systems where optical mixing transfers laser noise into an RF or sensing signal. Examples discussed for this class of source include coherent communications, microwave and RF photonics, frequency synthesis, spectroscopy, interferometric sensing, distributed sensing, and LiDAR. The demonstrated device does not establish performance for every application, but it shows how high optical power and narrow linewidth can be pursued within a heterogeneous photonic integrated circuit.

For system designers, the key lesson is to assess the cavity as a whole. Waveguide loss, grating bandwidth and reflectivity, ring-filter loss, output coupling, and thermal mode control all influence the balance between linewidth, power, and single-mode behavior. The E-DBR emphasizes high power with a roughly kilohertz linewidth; the ring-assisted version reaches a narrower linewidth with lower output power.

Conclusion

Heterogeneous silicon/III-V integration makes it possible to combine semiconductor gain with long, low-loss silicon reflectors on a single platform. The reported E-DBR and RAE-DBR results show that narrow linewidth depends not on one component alone, but on matching the cavity design to waveguide loss, filtering requirements, and operating conditions. Engineers evaluating such sources should weigh linewidth targets against output-power needs and plan for tuning to maintain alignment and stable single-mode operation.

Access Official Technical PDF

About The Author