Access Official Technical PDF

Share Summary:LinkedInEmail

A K30 series PID controller is a configurable, panel-mounted instrument for temperature and other process-control applications. The series uses a two-degree-of-freedom PID algorithm and includes five model sizes: K32, K33, K34, K37, and K39. For engineers and integrators, reliable commissioning depends on matching the controller’s input and output configuration to the field devices, then setting the control and alarm functions for the application.

K30 series PID controller models and I/O options

The models differ in panel dimensions and available options, so selection should begin with the required cutout and I/O. Depending on model and option code, the series can provide relay, SSR voltage-pulse, or 4–20 mA SCR control output, as well as alarm outputs. Some configurations also offer retransmission or digital input for selecting preset set values.

The K32, K33, and K39 are listed with basic functions; the K34 and K37 have specified option configurations. Available features are not identical across every model. Check the selected model’s terminal arrangement and option code before designing panel wiring. For example, digital input can support external selection of SV1, SV2, or SV3 where the relevant option is present. Retransmission options can send a selected process value, set value, or manipulated variable as a 4–20 mA signal.

Match the sensor input and control output

The controller accepts multiple input types, including thermocouples, RTDs, 4–20 mA current, and voltage signals. Thermocouple choices include K, J, T, E, R, B, S, L, N, U, C, and D types; RTD choices include JPt100 and Pt100 variants. The input type and range must match the installed sensor and the process. For current input, the manual specifies a 250-ohm resistor at the input terminals. For 1–5 V input, an internal jumper must be moved to the designated position.

Output selection determines how the controller drives the final control element:

  • Relay ON/OFF: A straightforward switching mode, identified for applications such as cooling control.
  • SSR voltage pulse: A PID output intended for an SSR input.
  • SCR current output: A 4–20 mA PID signal for a thyristor power regulator module.
  • Relay PID: PID control through relay contacts; the manual notes contact wear and limitations for applications requiring a fast response.

Output availability and alarm-output behavior can depend on model and configuration. In particular, the K34-S00 basic model has a documented alarm-output consideration when the control output is configured for SSR or SCR. Confirm the relevant wiring diagram rather than assuming all models share the same terminal behavior.

Commissioning: configure first, then tune

Before applying power, verify the supply rating, terminal assignment, sensor polarity, and external wiring. The controller is intended for indoor panel mounting. Turn off power for wiring and maintenance, and do not touch terminals while energized. Where a controller failure could create a hazard or damage valuable equipment, use a separate safety device; the PID controller should not be the sole protective measure.

The factory defaults are a K-type thermocouple input and SSR output selection. These may not suit the application. Set the input type and output type in the input/output setting mode before adjusting other parameters. Changing the input type restores other parameters to factory defaults, so the control settings must then be checked and configured again.

After confirming the input and output, set the required process set value (SV). The manual recommends auto-tuning before first operation: select a set value representative of the range used most often, then start the tuning function. The AT indicator flashes during the process and turns off when tuning is complete. Avoid key operation while tuning is in progress.

Auto-tuning is not appropriate for every process. The manual cautions against using it where temporary ON/OFF output is unacceptable, where the process responds rapidly, or where a temporary overload must be avoided. In those cases, evaluate the application constraints and set or verify the PID parameters accordingly.

Alarms, monitoring, and signal functions

Where supported by the configuration, two alarm outputs can be assigned from a range of alarm types, including absolute-value limits, deviation limits, and combined upper/lower limits. Alarm behavior can include hysteresis and a delay. A hold function is available for specified low-alarm types to prevent an unwanted alarm during startup before the process first crosses the alarm threshold.

The control loop break alarm (LBA) is available through Alarm 1. It monitors for a lack of process-value change under specified conditions when the PID calculation remains at 0% or 100%. This can help indicate issues such as a heater fault, sensor problem, wiring issue, or output-circuit problem. LBA is not a substitute for fault diagnosis: the manual notes that disturbances may trigger it, and an unsuitable or overly short setting can cause abnormal operation. It is inactive during auto-tuning.

Additional functions can support commissioning and operation. The manipulated-variable display shows output as a percentage, while input filtering can help address noise or fluctuation. Input correction allows a measured value to be compensated. For voltage or current inputs, users can configure scaling and decimal-point position. Retransmission can be assigned to PV, SV, or MV; the option may also provide sensor power supply (SPS), specified as 15 V DC, 25 mA.

Practical checks for a reliable installation

Before placing the loop in service, confirm that the configured sensor type, input range, output mode, and alarm assignments match the actual hardware. Verify that the controller is securely mounted in the panel and that wiring follows the terminal diagram for the exact model and options. Review setpoint limits, alarm thresholds, and any retransmission scaling, then confirm that the displayed process value responds as expected.

The K30 series provides a flexible set of control and monitoring functions, but correct operation rests on application-specific configuration. Selecting the right model and I/O, setting the input before other parameters, and tuning with process constraints in mind help integrators and plant teams establish a control loop that is easier to commission and monitor. Safety interlocks and independent protective devices remain essential wherever a control failure could have serious consequences.

Access Official Technical PDF

About The Author