Kesterite solar cells are attracting interest as a potential route to thin-film photovoltaics made from more abundant, relatively low-toxicity elements. Their absorber materials include copper zinc tin sulfide (CZTS), copper zinc tin selenide (CZTSe), and mixed sulfur-selenium compounds (CZTSSe). The appeal is clear: kesterite can absorb light efficiently in a layer only a few microns thick, and its composition avoids the indium and gallium used in CIGS absorbers. But promising material properties do not by themselves make a commercially ready device. Progress depends on controlling composition, defects, interfaces, and manufacturing conditions together.
Why kesterite is being explored
Kesterite belongs to the chalcogenide family of semiconductors. Its composition combines copper, zinc, tin, and sulfur and/or selenium. Replacing indium or gallium with tin and zinc offers a way to build a photovoltaic absorber from elements that are more abundant and generally less toxic. This makes kesterite an area of interest for researchers seeking to reduce material supply and environmental concerns in thin-film solar technology.
The material also has useful optical characteristics. Kesterite has a direct bandgap in the approximate range of 1.0 to 1.5 eV and a high absorption coefficient, reported at about 105 cm-1. In practical terms, this means it can absorb incident light within a relatively thin film. Its bandgap can also be adjusted by changing the sulfur and selenium content, giving researchers options for tailoring the absorber composition.
These strengths need to be considered alongside device performance. The review reports a CZTSSe efficiency record of 12.6% in 2014, while noting that kesterite devices remained less efficient than CIGS at the time. The central challenge is to convert the material’s resource and processing advantages into dependable, higher-performing devices.
Kesterite solar cells: manufacturing routes
Conventional kesterite fabrication uses vacuum-based deposition, including co-evaporation of metal elements or sputtering of metallic precursors. The deposited material is then crystallized at high temperature in a sulfur- and/or selenium-containing atmosphere. The thermal treatment forms the absorber, but it also makes process conditions important: composition can change during heating and cooling, and unwanted phases can develop.
Researchers have also investigated vacuum-free approaches, which broadly include:
- Electrochemical deposition from solutions.
- Printing or coating from precursor solutions.
- Printing or coating from particle-based solutions.
Solution-based deposition is notable because it has been used in many of the high-performing devices discussed in the review, challenging the assumption that wet-processed films necessarily perform worse than vacuum-deposited ones. Non-vacuum methods may also offer potential cost and composition-control advantages. However, the deposition method alone does not determine device quality: it must be matched with suitable chemistry, thermal processing, and control of the final film.
Composition, defects, and carrier recombination
High-performing kesterite absorbers are commonly made under copper-poor and zinc-rich conditions. The crystal structure can accommodate copper-rich or copper-poor compositions without changing its overall structure, although the distribution of atoms within the lattice can differ. This flexibility is useful, but it also makes precise control of composition and defect populations essential.
Several intrinsic defects influence electrical behavior. Copper vacancies (VCu) and copper atoms on zinc sites (CuZn) act as acceptors, while zinc atoms on copper sites (ZnCu) act as donors. In copper-poor material, copper vacancies are especially relevant to intrinsic p-type doping. The balance among these defects can affect charge transport and recombination—the loss of photogenerated carriers before they can contribute to electrical output.
Other process-related effects can complicate defect control. Tin-chalcogenide species are volatile, so high-temperature processing and subsequent cooling can lead to tin loss. This can leave the absorber tin-poor and contribute to unwanted defects or secondary phases. Researchers have explored extrinsic dopants from several element groups, including germanium and alkali metals such as sodium. The review describes reported benefits associated with germanium, including reduced tin loss and fewer deep defects, and links sodium treatment to changes in grain size and carrier concentration. These effects depend on the material and process; they are not a substitute for controlling the full absorber formation sequence.
Interfaces and device architecture
A typical kesterite cell uses a layered structure. A glass substrate supports a molybdenum (Mo) back contact, followed by the p-type kesterite absorber and an n-type buffer layer, commonly cadmium sulfide (CdS). An intrinsic zinc oxide layer and aluminum-doped zinc oxide (AZO) provide additional layers toward the front contact, where narrow metal strips collect current.
Layer selection matters because interfaces can influence charge collection and recombination. The CdS buffer has been widely used, but its cadmium content raises safety concerns, and the band alignment between CdS and kesterite is not ideal. Zinc-based alternatives—including Zn1-xSnxOy, Zn(O,S), and ZnS—have been investigated as ways to improve interface behavior and explore cadmium-free designs.
Thermal processing can also drive elements to diffuse between layers, creating secondary phases near the absorber interfaces. Examples discussed in the review include copper sulfide near the buffer and zinc sulfide or tin sulfide near the back contact. Such phases can disrupt band alignment and interfere with charge extraction. At the rear interface, sulfurization or selenization can form MoS2 or MoSe2 between kesterite and molybdenum. Depending on its thickness, this layer can impede charge collection. Alternative back contacts and thin intermediate layers have therefore been explored.
Practical implications for development
Kesterite’s potential rests on more than replacing one absorber material with another. Device development requires coordinated decisions across precursor composition, deposition, thermal treatment, doping, buffer selection, and contact engineering. Improvements in one area may not translate into better performance if another part of the stack introduces recombination or blocks carrier extraction.
For engineers and technical decision-makers, the key takeaway is that kesterite remains a promising research-stage photovoltaic platform, not a drop-in solution whose material advantages alone ensure commercial readiness. The main priorities identified in the review are reducing harmful secondary phases, understanding how growth conditions determine composition and defects, limiting carrier recombination, and designing device architectures specifically for kesterite. Progress on these connected challenges will determine whether its abundance and processing options can be translated into practical, competitive thin-film solar cells.