Access Official Technical PDF

Share Summary:LinkedInEmail

Laser frequency noise is commonly described using a power spectral density (PSD), while laser coherence is also characterized by the optical spectrum, or lineshape. These measures are closely connected: at sufficiently high offset frequencies, features in the frequency-noise spectrum correspond to features in the optical lineshape at matching offsets from the laser’s central frequency. This relationship offers engineers a way to interpret laser behavior and understand how optical filtering can affect noise.

Why frequency noise and lineshape both matter

A laser’s electric field can be represented by a carrier with a time-varying phase. Fluctuations in that phase produce frequency variations, while the field’s correlation over time determines the measured optical spectrum. The lineshape describes how optical power is distributed around the central frequency; the frequency-noise PSD describes the strength of frequency fluctuations across baseband frequencies.

Both measures are relevant in applications that depend on temporal coherence, including coherent optical communications, sensing, spectroscopy, and imaging. In an idealized quantum-limited case, where spontaneous emission is the dominant noise source, the connection between frequency noise and linewidth is relatively simple. In practical situations, noise can have other characteristics, so linewidth alone may not fully describe the laser’s behavior.

The central relation between laser frequency noise and lineshape

The central relation links the frequency-noise PSD at an offset frequency to the optical spectral density on either side of the laser’s central frequency at the corresponding offset. In simplified terms, the frequency-noise PSD divided by the square of the offset frequency is proportional to the sum of the two optical spectral-density values, normalized to the laser power.

This result identifies a high-frequency correspondence: a feature in the frequency-noise spectrum at a particular baseband offset appears in the optical lineshape at the same frequency offset above and below the optical carrier. For a symmetric laser lineshape, the two sides carry matching features. The relation does not depend on a particular physical origin of the frequency noise.

The high-frequency condition matters. The authors indicate that offsets greater than roughly ten times the optical lineshape’s full width at half maximum (FWHM) can be treated as sufficiently high as a practical rule of thumb. This is not a universal boundary for every measurement; it describes the range in which the approximation was found to apply in the reported work.

What measurements can reveal

The relationship can help engineers compare two views of the same laser rather than treating the linewidth and frequency-noise PSD as unrelated specifications. A narrow optical spectrum does not, by itself, show how noise is distributed across every offset frequency. Conversely, a frequency-noise measurement can show localized features that may also be visible as structure in the optical spectrum.

In the reported experiment, frequency noise was measured using a Mach-Zehnder interferometer (MZI), a balanced photodetector, and a spectrum analyzer. The optical lineshape was measured by beating the laser against a narrow-linewidth fiber laser and measuring the resulting signal spectrum. A jitter feature in the phase-noise PSD corresponded to symmetrical bumps in the measured lineshape. This agreement supported the predicted connection.

For practical interpretation, engineers can use the relationship to:

  • Compare frequency-noise features with spectral features at corresponding offsets.
  • Check whether a measured optical-spectrum bump is associated with a feature in the baseband noise spectrum.
  • Consider measurement bandwidth and resolution when deciding whether individual spectral features can be resolved.

How optical filtering can shape frequency noise

The relation also describes an effect that may be less intuitive: optical filtering can alter the laser’s frequency-noise PSD. For a symmetric optical filter centered on the laser frequency, the output noise PSD at a sufficiently high baseband offset is modified according to the filter’s power transmission at the corresponding optical-frequency offset.

In other words, transmission at optical frequencies on the sides of the carrier maps to frequency noise at the matching baseband frequency. A filter can therefore shape noise in a selected frequency region by attenuating the relevant portions of the optical lineshape. The reported experiment used an MZI with a free spectral range of 203 MHz. With the laser aligned to a transmission maximum, the measured change in frequency noise followed the MZI’s transmission spectrum.

This result is not a claim that filtering improves every laser or application. The useful noise region depends on the system. The paper notes that phase noise can be estimated by integrating frequency-noise PSD across a range determined by acquisition time and sampling or modulation frequency. Consequently, noise near the application’s sampling or modulation frequency can be particularly relevant to system performance.

Practical implications for laser-based systems

For engineers selecting or integrating lasers, the central relation provides a framework for connecting optical-spectrum measurements with frequency-noise data. It can also inform evaluation of optical filtering when noise reduction or spectral shaping is a design objective. The key is to match the frequency ranges: interpret high-offset frequency noise alongside the optical spectrum at the corresponding carrier offsets, while accounting for the limits of the high-frequency approximation and the measurement setup.

Laser linewidth remains useful, but it is only one summary of coherence. Considering both the frequency-noise PSD and lineshape gives a more detailed picture of where fluctuations occur and how optical components may affect them. That perspective supports better-informed decisions in coherent, sensing, and other laser-based systems where phase stability matters.

Access Official Technical PDF

About The Author