Access Official Technical PDF

Share Summary:LinkedInEmail

In accelerator kicker systems, a switching delay can matter: during an asynchronous beam-abort request, energy from an uncontrolled beam may damage downstream equipment. Light-triggered thyristors offer one way to initiate semiconductor switching with an optical pulse rather than relying only on an electrical gate signal. Their potential value depends on more than trigger speed, however. Engineers must also account for optical absorption in silicon, device behavior, electromagnetic interference (EMI), voltage sharing, and the practicalities of maintaining a reliable system.

Why consider optical triggering in kicker systems?

Segmented extraction kicker systems place demanding requirements on their solid-state switches. Low turn-on delay is important when the system must respond quickly to a beam-abort request. At the same time, the switching arrangement must support high reliability, availability, and fault tolerance.

Electrical triggering brings its own design challenges. Many bipolar power semiconductors require substantial gate current, and the trigger circuit must deliver the intended pulse despite noise and coupling effects. In sensitive systems, even a small fraction of the nominal gate pulse may risk unintended conduction. Triggering robustness is therefore a system-level concern, not simply a matter of selecting a switch.

Other constraints include maintenance access, sourcing, and operating-voltage limits. Limited radiation hardness can require multiple semiconductor devices to be connected in series to reach the necessary voltage rating. That arrangement adds requirements for managing the behavior of each device in the stack.

How optical absorption enables thyristor triggering

Optical activation starts when photons enter semiconductor material and transfer energy to electrons. For absorption to generate an electron-hole pair, the photon must provide sufficient energy to move an electron across the material’s band gap. The process also has to satisfy momentum conservation. In silicon, this makes optical absorption dependent on wavelength and on the semiconductor’s band structure.

The wavelength must be selected with both photon energy and penetration depth in mind. The workshop material notes that wavelengths above roughly 1100 nm do not provide enough photon energy for electron-hole pair generation in silicon. At shorter wavelengths, light may be absorbed close to the surface, limiting penetration and increasing the likelihood of carrier recombination near that surface. These considerations help explain why the optical source and the device’s illuminated structure must be designed together.

Light-triggered thyristor approaches

Light-triggered thyristors with an optical gate region

One light-triggered thyristor (LTT) design places a break-over diode and multiple amplifying gate structures in the device’s central region. The break-over diode is located within the light-sensitive area. An optical pulse generates carriers in that region, supporting the device’s transition into conduction. The example pulse parameters presented for this type of device include a 40 mW, 10-microsecond pulse at a wavelength between 850 and 1000 nm; these are illustrative values, not universal design requirements.

Laser-pumped silicon thyristors

A laser-pumped silicon thyristor uses a laser diode array to illuminate the semiconductor. In the described arrangement, openings are patterned in the anode metallization so that light can reach the device. For series-connected stacks, each thyristor has a separate photon source, with stage-to-stage connections between devices. This approach illustrates how optical delivery and electrical stacking must be considered together.

The workshop material reports a measured delay of 5 ns between the laser-driver current and switch current for one configuration. It also gives an example using a 650 W peak optical pulse, 170 microjoules of energy, a 400 ns full width at half maximum, and a 1000 nm wavelength. These values describe the cited example and should not be treated as general performance specifications.

Laser-gated and pumped concepts

Another concept combines an initial laser pulse with continued illumination. The initial pulse triggers the device, while subsequent illumination is intended to reduce forward dissipation. The presentation describes both direct, on-board illumination and indirect, off-board illumination arrangements. It also reports single-shot operation for 16.4 kV devices, with current density and rate-of-rise values given for that particular demonstration. Such reported results are specific to the device and test conditions.

What CERN’s investigations examine

The investigations described use commercially available, low-cost phase-control silicon-controlled rectifiers (SCRs), activated by illuminating their gate regions. A key part of the work is measuring the relationship between optical energy and the beginning of conduction. A CCD camera is used to image the wafer’s illumination profile with a 905 nm source, helping map which areas receive light above the observed triggering threshold.

That illuminated area matters because the initial conducting region influences how current spreads through the device. The area at turn-on is linked to the thyristor’s allowable rate of current rise, or di/dt. If current rises too quickly through a small initial conduction region, the device may face increased stress. Mapping the light distribution therefore helps connect optical pulse conditions with an electrical design constraint.

The reported electrical tests identify a 12-microjoule pulse energy as a threshold at which the SCR begins turning on slowly. This is an observation from the described test setup, not a general threshold for other thyristors. The work also considers two SCRs connected in series. In that configuration, limitations in the fiber-coupled light source and the need to balance voltage across the devices are important. Small differences in switching behavior may be compensated for with a snubber circuit.

Practical implications for system designers

Optical triggering can change how a pulsed-power switch is initiated, but it does not remove the need for careful system engineering. Design reviews should consider:

  • Optical delivery: Confirm that light reaches the intended sensitive region and that the source, wavelength, pulse energy, and timing suit the device under evaluation.
  • Switching behavior: Assess turn-on delay, conduction development, and current rise in the context of the application’s operating conditions.
  • Series operation: Account for voltage sharing and differences in commutation behavior when multiple switches are stacked.
  • Trigger robustness: Evaluate the complete triggering arrangement alongside the system’s exposure to EMI and unintended activation.
  • Maintainability and sourcing: Include optical components, connections, and device availability in the system-level assessment.

For kicker-system engineers and integrators, the central lesson is that light-triggered thyristors are not a drop-in answer to every switching challenge. Their suitability depends on matching optical absorption and illumination to the device, then validating the resulting electrical behavior—including current rise and stack voltage balance. A coordinated assessment of the semiconductor, trigger source, and system requirements is essential before adopting optical activation in a pulsed-power design.

Access Official Technical PDF

About The Author