Access Official Technical PDF

Share Summary:LinkedInEmail

Choosing an audio power amplifier for a compact radio involves more than matching output power to a speaker. Noise, distortion, supply voltage, and electromagnetic coupling can all affect system performance—particularly in AM receivers, where the antenna may be close to the amplifier and its wiring. The LM1895 audio amplifier and its higher-voltage counterpart, the LM2895, were designed with these concerns in mind, using a compensation approach intended to support low noise and reduced AM radiation.

LM1895 audio amplifier: designed for sensitive applications

The LM1895 is a low-voltage audio power amplifier intended for applications such as compact AM-FM radios, battery-operated tape players, and line drivers. Its operating supply range is listed as 3V to 10V in the electrical characteristics, with 6V used for the principal output-power test condition. At 6V into a 4-ohm load, the data sheet specifies 0.9W minimum and 1.1W typical output power at 10% total harmonic distortion (THD). At 9V into an 8-ohm load, the listed output power is also 1.1W typical.

The LM2895 is intended for applications requiring a higher supply voltage. Its listed operating range is 3V to 15V, and its electrical characteristics include tests at 12V. At that supply, the specified output power is 3.6W minimum and 4.3W typical into 4 ohms at 10% THD; into 8 ohms, the listed value is 2.5W. These are test-condition figures, not a substitute for checking the complete circuit’s load, thermal, and distortion requirements.

Both devices specify low noise and low crossover distortion as design features. The LM1895 comes in an 8-pin miniDIP package, while the LM2895 uses an 11-lead single-in-line package. Package choice and thermal behavior should be considered alongside the electrical requirements. The data sheet notes that the LM2895 package has a somewhat degraded thermal characteristic relative to the earlier design and that allowable operation depends on mounting and ambient temperature.

Why amplifier noise matters in AM radio design

In an AM radio, the loopstick antenna can be physically close to the audio amplifier. Current in the speaker and supply leads can couple electromagnetically into the antenna, potentially causing interference or system oscillation. Noise radiated by the amplifier can also degrade receiver sensitivity and signal-to-noise performance.

The LM1895’s compensation scheme is intended to address these issues while supporting low noise and reduced AM radiation compared with conventional amplifier designs. The data sheet gives equivalent input-noise figures of 1.4 microvolts under its CCIR/ARM measurement and 2.0 microvolts wideband, with a 20Hz to 20kHz bandwidth specified for the wideband test. It also reports 40dB minimum and 52dB typical power-supply rejection at 1kHz under the stated test conditions. These figures help characterize the device, but actual system results depend on the circuit, board layout, and surrounding radio design.

Compensation and external components

External components are part of the amplifier’s operation, not simply supporting accessories. In the application circuit, the compensation capacitor, C1, helps stabilize the amplifier and set its bandwidth. Limiting closed-loop bandwidth can be useful in an AM radio design, where unnecessary high-frequency response may increase noise exposure. The data sheet provides a curve relating the -3dB bandwidth to voltage gain; designers should use it when selecting gain and compensation values together.

The gain-setting resistors establish the closed-loop voltage gain according to the relationship Av = 1 + R1/R5. Other components serve distinct roles:

  • Input coupling capacitor: Blocks DC at the input. Together with the input resistance, it sets a low-frequency response pole.
  • Feedback capacitor: Helps ensure unity gain at DC and contributes a low-frequency pole with the feedback resistance.
  • Bootstrap capacitor and resistor: Support drive to the output stage; their values also affect low-frequency behavior.
  • Output coupling capacitor: Isolates the load from the amplifier’s DC output level. Its interaction with load resistance sets another low-frequency pole.
  • Supply bypass capacitor: Provides power-supply filtering, while the capacitor identified for improved supply rejection affects power-supply rejection and turn-on delay.

Because several capacitor-resistor combinations influence the low-frequency response, changing one component can affect more than a single design target. Component values should be reviewed as a set, with attention to bandwidth, gain, stability, and the intended load.

Design checks for implementation

For a practical design review, confirm that the selected device matches the supply and output requirements, then assess the external network and thermal conditions. The data sheet lists 8mA typical supply current for the LM1895 and 12mA typical for the LM2895 under its stated quiescent test conditions. Output current and power dissipation during operation will also matter when evaluating thermal limits.

In AM radio equipment, pay particular attention to the placement and routing of speaker and supply leads relative to the loopstick antenna. The application discussion identifies these conductors as possible coupling paths. Keep the intended circuit bandwidth in view as well: the compensation capacitor influences both stability and bandwidth, and gain selection is linked to the available bandwidth guidance.

The data sheet also specifies no turn-on pop and smooth waveform clipping as device features, alongside tested low crossover distortion. For distortion comparisons, note the conditions: the table gives 0.27% at 50mW and 0.20% at 0.5W at 1kHz for both devices, while the LM1895 lists 0.15% at 1W. Results at other frequencies, power levels, supplies, or loads may differ.

Practical implications

The LM1895 and LM2895 bring together audio output capability, external bandwidth compensation, and features aimed at reducing noise and AM interference. The LM1895 suits lower-voltage designs, while the LM2895 extends the supply range for applications needing greater output power. For engineers and integrators, successful use depends on selecting the appropriate device and load, designing the compensation and coupling network carefully, and treating board layout and thermal conditions as part of the amplifier design—not as afterthoughts.

Access Official Technical PDF

About The Author