Access Official Technical PDF

Share Summary:LinkedInEmail

The LM358 and LM324 are widely used general-purpose operational amplifiers, but successful LM358 and LM324 design depends on understanding their distinctive input and output stages. These devices can operate from a single supply and produce an output close to the negative rail under suitable loading. They are not rail-to-rail amplifiers, however, and their response to input voltage, output current and changing load conditions can differ from that of newer op amps. Accounting for these characteristics early helps engineers avoid unexpected clipping, phase reversal and signal distortion.

Check input common-mode limits first

The recommended input common-mode range extends from the negative supply to approximately 2 V below the positive supply over the specified operating temperature range. The upper limit can shift with temperature, so a design that works at room temperature may have less margin in colder conditions. At low supply voltages, the available input range narrows further: with a 3 V supply at -40°C, the cited range is 0 V to 1 V.

In an inverting amplifier, the input pins can often be held at a fixed bias voltage, making it easier to stay within the common-mode range. With non-inverting or changing input signals, check the full signal range against the device limits rather than relying on the supply voltage alone.

Inputs below the negative rail can forward-bias parasitic junctions. This may cause excessive input current and phase reversal, where the output moves in the opposite direction from the expected response. In a single-supply system, negative inputs should therefore be avoided unless the application can tolerate an undefined or reversed output during the event. If negative voltage cannot be prevented, a series input resistor can limit current; the application guidance recommends limiting it to 1 mA or less. Also observe absolute maximum ratings: an input above the positive supply may be tolerated in some conditions, but exceeding the specified maximum can cause device damage.

Understand the output stage and its load

The family’s output stage can pull low near the negative supply when the load and its termination help the internal sink driver. A load of 10 kΩ or less connected to the negative rail supports the low-output-voltage condition described in the device specifications. When a load or feedback network is instead connected to a positive voltage, the amplifier must sink current to drive low. At light sink currents, the internal constant-current sink can maintain a low output; at higher currents, a PNP output transistor takes over and the low voltage rises.

This makes load termination an important design choice. If a low output level is essential, use a sufficiently high resistance or, where practical, terminate the load and feedback network to the negative supply. When significant sink current is required, input common-mode voltage and junction temperature can also affect the available output current.

The high output level has a different limitation. The output uses a Darlington NPN stage, so it does not reach the positive supply rail. The specified high-level output is approximately 1.5 V below the supply under the stated 5 V supply and 2 kΩ load condition. Allow additional headroom for load current and temperature; do not assume the output swing is fixed at a supply-independent rail-to-rail value.

The output’s short-circuit current limiting does not make prolonged shorts safe. Dissipation depends on the voltage across the device and the output current, and the family does not include over-temperature shutdown. Follow the device’s absolute maximum ratings and avoid sustained short-circuit conditions.

Account for slew rate and crossover delay

Slew rate and bandwidth are typically specified rather than production-tested, so leave margin between typical values and the circuit’s requirements. Typical slew rate varies by channel count and device variant. The “B” variants have a typical slew rate of 0.5 V/µs and bandwidth of 1.2 MHz; other variants have different typical values. Positive and negative slew rates may not always match, so do not depend on closely matched transitions unless the selected device and application support that expectation.

A further consideration is crossover delay. The output stage does not apply the static bias used by a Class AB output, which helps the device pull low but can leave a delay when it switches between sourcing and sinking current. During this interval, the output may flatten or step before recovering. The effect is more relevant with high-frequency signals, fast transitions, changing load-current polarity or tight distortion requirements.

Where appropriate, a pull-up or pull-down resistor can keep one output driver active and reduce switching between source and sink operation. Evaluate the resistor’s effect on output swing, current and power dissipation, and test the circuit with its actual load conditions.

Designing at low supply voltage

The family’s minimum supply voltage is 3 V, but operating near that limit calls for careful checks of both input and output range, particularly at the lowest operating temperature. At 3 V and -40°C, output capability depends strongly on load. A bidirectional 100 µA load has a typical output range of about 0.75 V to 1.5 V; lighter bidirectional loading can extend the range.

An external pull-up resistor can raise the high output level, but it changes the load on the output stage. Lower resistance may improve the high level while degrading the low level and increasing power consumption. Account for the amplifier’s constant sink current and all other loads when selecting the resistor. Typical curves are useful for initial design, but they are not a substitute for design margin across operating conditions.

Using an op amp as a comparator

An LM358 or LM324 can serve as a comparator in some applications, such as when timing requirements are not demanding or an amplifier channel is otherwise unused. It is not a direct replacement for a comparator when propagation timing matters. The output takes finite time to recover after an overload, and recovery from a low output can vary with the non-inverting input’s common-mode voltage.

For comparator-style use, verify input offset, common-mode range and both output levels. Keep at least one input within the valid common-mode range. If both inputs exceed the upper limit, the output may be either high or low; inputs below the negative rail can also cause phase reversal. These conditions make checking the complete input range essential.

Conclusion

Reliable LM358 and LM324 designs begin with the device’s actual operating limits, not an assumption of rail-to-rail behavior. Check common-mode voltage over temperature, choose load terminations that support the required low output, allow headroom below the positive rail, and consider crossover delay when signals or load currents change quickly. At low supply voltage or in comparator applications, verify input and output behavior under the full range of expected conditions and retain margin around typical performance.

Access Official Technical PDF

About The Author