In data-acquisition designs that combine 5V analog circuitry with lower-voltage digital logic, the MAX1202/MAX1203 ADCs bring conversion, channel selection and serial communication into one device. These 12-bit successive-approximation converters include an eight-channel multiplexer and track-and-hold circuitry, with selectable single-ended or differential inputs. Their adjustable digital-output supply also supports direct interfacing with logic levels from 2.7V to 5.25V, helping engineers connect analog measurement stages to different processor or controller domains.
The devices are intended for applications including process control, battery-powered instruments and other measurement systems. Their practical value depends on more than resolution: input configuration, reference quality, serial timing and power-state choices all influence how they fit into a complete acquisition path.
MAX1202/MAX1203 ADCs for mixed-voltage acquisition
Both converters operate from a +5V analog supply, with the option of a 0V or -5V negative supply. The separate VL pin sets the positive logic-output level for DOUT and SSTRB, allowing those outputs to match a system’s digital supply without changing the analog supply. The digital inputs are designed to accept 3V or 5V logic.
The MAX1202 includes an internal nominal 4.096V reference. The MAX1203 instead uses an external reference. Both devices provide a reference-buffer amplifier, and the reference arrangement can be selected to suit the design. This distinction matters when specifying the converter: reference choice affects the full-scale input range and the surrounding circuitry required.
At 12-bit resolution, the converter can represent an input with 4,096 output codes. With a 4.096V reference, the nominal unipolar range is 0V to 4.096V, corresponding to 1mV per LSB. In bipolar mode, the nominal range is -2.048V to +2.048V. The source specifies relative accuracy of ±0.5 LSB for A-grade parts and ±1 LSB for B-grade parts; actual system accuracy also depends on reference, input conditioning, grounding and other design choices.
Choosing single-ended or differential inputs
The eight analog pins can be configured as eight single-ended channels or four differential channel pairs. In single-ended operation, the selected input is measured relative to ground. In differential operation, the converter selects a positive and negative input from a paired set of channels and measures their difference.
This is a pseudo-differential architecture: the converter samples the positive input, while the negative input provides the return reference. That return must remain stable relative to ground during conversion. The device documentation recommends keeping the negative input stable to within approximately ±0.5 LSB, or ±0.1 LSB for best results, and describes connecting a 0.1µF capacitor from the selected negative input to ground.
Input source impedance also affects acquisition. The internal track-and-hold needs time to charge its sampling capacitance; higher source impedance increases the time required. The specified acquisition time is at least 1.5µs, and source impedances below 1kΩ do not significantly affect AC performance. If a higher impedance source is used, an input capacitor may help, but it creates an RC filter with the source and therefore limits signal bandwidth.
Serial interface and conversion timing
A four-wire serial interface carries configuration and conversion data. The devices are compatible with SPI and MICROWIRE interfaces, and provide a serial strobe output for timing coordination with supported digital signal processors. The serial clock can be used both to transfer data and, in external-clock mode, to drive the successive-approximation conversion. The interface supports clock rates up to 2MHz, subject to the selected operating mode and timing requirements.
Each conversion begins with a control byte that selects the channel, unipolar or bipolar operation, single-ended or differential mode, and clock or power-down setting. The first logic-high bit received while chip select is low marks the start of that control byte. In external-clock mode, a conversion can take 15 clocks, and the source specifies a 133ksps sampling rate under the stated operating conditions. The total conversion sequence also depends on the serial clock and any idle time between transfers. The documented software sequence advises keeping total conversion time within 120µs to avoid excessive track-and-hold droop.
Internal-clock mode separates conversion timing from the processor’s data-read timing. The converter performs the conversion using its internal clock, then stores the result for serial readout. SSTRB indicates conversion progress and completion. This can be useful when the processor cannot provide a continuous conversion clock, while external-clock mode gives the system more direct control of conversion timing.
Reference, layout and signal integrity
Reference implementation should match the chosen part and compensation mode. The MAX1202 can use its internal reference or an external one; the MAX1203 requires an external reference. An external reference may be applied at REF or, through the buffer arrangement, at REFADJ. When driving REF directly, the internal buffer must be disabled by tying REFADJ to VDD. The data sheet also specifies bypassing a noisy or higher-impedance reference close to REF.
Board layout is part of the measurement design. Keep analog and digital signal paths separated, avoid routing clock lines alongside analog inputs, and use a short, low-impedance return for the analog ground connection. The recommended approach establishes a single-point analog ground and bypasses the supply pins close to the converter. These measures help limit the impact of digital switching and supply noise on conversion results.
Using power-down modes to manage consumption
The MAX1202/MAX1203 offer hardware shutdown through SHDN and software-selectable power states through the control byte. The device can enter fast or full power-down between conversions, then power up when the serial interface is accessed. Typical operating current is 1.5mA; the specified typical current in full power-down is 2µA, with a maximum of 10µA under stated test conditions. Actual consumption depends on operating conditions and digital-input states.
Power-down strategy involves a trade-off between current and readiness. Reference-buffer compensation affects power-up delay and maximum conversion rate. For example, the data sheet specifies that external compensation with a 4.7µF capacitor supports the 2MHz clock rate, while internal compensation allows shorter power-up times but limits the external conversion clock to 400kHz. Reference settling and the time spent between samples should therefore be considered alongside the desired sampling rate.
Practical design implications
The MAX1202/MAX1203 combine multiplexed inputs, track-and-hold conversion and flexible serial communication in a compact 12-bit acquisition solution. For engineers and system integrators, the key decisions are how to pair and condition inputs, which reference arrangement to use, whether internal or external clocking best suits the controller, and how to balance power-down savings against startup and settling time. Careful attention to those choices—and to analog layout and serial timing—helps ensure the converter is integrated in a way that supports the measurement requirements of the wider control or instrumentation system.