Access Official Technical PDF

Share Summary:LinkedInEmail

Electronic beam steering lets an antenna change its pointing direction without mechanically moving the array. At the heart of this approach is the MEMS phase shifter: a controlled RF component that changes the phase of a signal feeding an antenna element. A proposed eight-element X-band design illustrates how suspended capacitive bridges can provide this control, while also showing why transmission-line transitions and impedance matching matter in an integrated phased array antenna.

Why phase control matters in a phased array antenna

In a linear array, multiple radiating elements are arranged at regular intervals. When signals reach those elements with a suitable phase relationship, their radiation combines to form a main beam in a chosen direction. Adjusting the relative phase between elements changes that direction, enabling electronic beam steering without moving the antenna hardware.

This capability is relevant to automotive radar applications such as adaptive cruise control, blind-spot detection and parking assistance. More broadly, phased arrays are useful where a system must direct or track a beam electronically. The array’s behavior depends not just on the radiating elements, but on the phase-control network that feeds them.

Phase shifters can provide either predefined, discrete phase states or continuous adjustment. The design described here uses discrete steps: each of its MEMS bridges contributes a nominal 15-degree shift. Coordinated settings across the array establish the phase progression needed for a selected beam direction.

How the MEMS phase shifter changes RF phase

The design places a series of conductive bridges above a coplanar waveguide (CPW) transmission line. Each bridge is suspended over the line and controlled separately. Applying an actuation signal creates an electrostatic force that pulls the bridge toward the underlying electrode. A dielectric layer prevents a direct electrical short when the bridge is actuated.

In the down, or ON, state, the bridge adds capacitive loading to the RF line. In the up, or OFF, state, it is farther from the line and has much less effect on the signal. Switching bridges therefore changes the line’s electrical loading and effective phase. This is a different physical mechanism from simply selecting between transmission paths of different lengths, though both approaches can be used to produce phase shifts.

The proposed phase shifter uses 24 individually controlled bridges. With a 15-degree phase increment per bridge, its control range is designed to cover 360 degrees. The authors used full-wave electromagnetic simulation to optimize the geometry for phase shift, insertion loss, return loss and matching to neighboring circuit sections. At 10.4 GHz, the reported phase-shifter results are approximately -1 dB insertion loss and -20 dB return loss in the stated bridge condition.

Integrating CPW phase control with microstrip antennas

A key integration challenge is that the antenna feed network and phase shifter use different transmission-line types. The array’s square patch elements are fed by microstrip lines, while the MEMS phase shifter is implemented on CPW. The design therefore places microstrip-to-CPW and CPW-to-microstrip conversion sections between the phase-control circuit and the radiating elements.

These transitions must connect the lines while limiting unwanted reflections and signal loss. Their design also needs to account for impedance matching and coupling between adjacent sections. In the reported simulation, the conversion unit achieved approximately -40 dB return loss and -0.1 dB insertion loss at 10.4 GHz. These values describe the modeled transition, not a general guarantee for other layouts or manufacturing processes.

The antenna itself is a one-by-eight linear array of square patch elements designed for 10.4 GHz on a Rogers 5880 substrate. Integrating the feed network, transitions, phase shifters and radiating elements allows the combined system—not just an isolated phase shifter—to be evaluated.

Simulated steering results and design implications

The analysis considers the array pointed at boresight and at a steered angle of 15.7 degrees. For the latter case, the required element phase settings are reported as 0, 60, 120, 180, 240, 300, 0 and 60 degrees. Since the design uses 15-degree increments, a 60-degree setting can be formed by actuating four bridges.

At boresight, the simulated main-beam gain is 15 dB, with a beamwidth of 10.6 degrees and a sidelobe level of -13.1 dB. At 15.7 degrees, the reported main-beam gain is 14.6 dB, beamwidth is 11.8 degrees and sidelobe level is -8.4 dB. These results illustrate that changing the phase settings steers the beam, while the simulated pattern characteristics also change with steering angle.

The work is a numerical design and analysis, rather than evidence of measured performance from a fabricated array. Its practical value is the integrated design approach: assess the phase shifter, transitions, feed network and antenna together, because each can affect the behavior of the complete RF system.

What engineers should take from the design

For engineers evaluating MEMS phase control, the example emphasizes several connected considerations:

  • Phase resolution: The 15-degree increments determine which phase states are available for steering.
  • RF losses and matching: Phase-shifter and transition performance both affect the signal delivered to the antenna elements.
  • Control coordination: Bridge states must be mapped to the phase progression required for the intended beam direction.
  • System-level analysis: Simulating the integrated array can reveal interactions that may not appear when components are considered separately.

The proposed design operates in X-band, while the authors identify the same design methodology as potentially applicable to other bands, including millimeter-wave frequencies. Any adaptation would require the relevant circuit and antenna structures to be designed and assessed for the target frequency; the X-band results should not be treated as proof of performance at another band.

Conclusion

A bridge-based MEMS phase shifter offers a way to introduce controlled, discrete phase changes in an RF feed network. In the simulated eight-element array, those changes enable electronic steering, with microstrip-to-CPW transitions connecting the MEMS circuitry to the patch antennas. For system designers, the central lesson is to treat phase control, impedance matching, transitions and radiation performance as parts of one integrated design problem. That approach provides a useful foundation for evaluating MEMS-based phased arrays in automotive radar and other RF applications.

Access Official Technical PDF

About The Author