Access Official Technical PDF

Share Summary:LinkedInEmail

A diaphragm metering pump is a reciprocating positive displacement pump: its repeated diaphragm movement draws liquid into a pump chamber and then displaces it into the discharge line. Reliable dosing depends on more than the pump itself. Installation conditions, valve orientation, piping design, operating pressure and stroke adjustment all affect whether the pump delivers consistently and safely.

For engineers, system integrators and plant teams, a disciplined approach to commissioning and maintenance helps protect the pump and connected equipment. The following principles explain the key checks and operating practices for this type of metering system.

How a diaphragm metering pump moves liquid

The drive and gear unit produce reciprocating movement, while the stroke-length adjustment controls the movement applied to the pump mechanism. In a diaphragm design, a double diaphragm separates the process liquid from the atmosphere. The suction and discharge valves open in response to pressure differences rather than being driven independently.

As the diaphragm moves through its suction stroke, pressure in the product chamber falls. The suction valve opens and liquid enters. During the discharge stroke, chamber pressure rises; when it exceeds the discharge-line pressure and the discharge valve’s opening pressure, liquid flows into the discharge line. The repeated cycle creates a pulsating flow.

Some designs include diaphragm rupture monitoring. If the process-side diaphragm is damaged, pressure between the diaphragm layers can rise. A hose connection, pressure gauge or pressure switch can provide an indication of the fault. Depending on the installation, a pressure-switch signal may be used to stop the pump or raise an alarm.

Plan installation around the process and the piping

Begin by checking the pump and accessories for transport damage and confirming the specified operating limits. The installation location should meet the pump’s documented environmental requirements. Mount the unit without strain, with the push-rod axis horizontal and valve axis vertical, and leave access for routine tasks such as checking the oil, adjusting the stroke and servicing the pumphead.

Electrical connections must be made by qualified personnel in line with local requirements. Confirm the motor supply and rotation direction before operation, and provide appropriate overload protection. Requirements for hazardous areas must also be observed where applicable.

Design suction and discharge lines for pulsating flow

Metering pump piping must accommodate the flow’s pulsating character. Poorly designed lines can contribute to cavitation, excessive pressure loads or excessive delivery. Keep piping clean and mechanically supported, avoid transferring pipe weight to the pump, and arrange connections so that valves and pumpheads can be removed for service.

Relevant factors include liquid density, vapour pressure, viscosity, suction and discharge pressures, elevation, pipe length and diameter, bends, and fittings. A high suction lift or restrictive suction line can make it difficult for the pump to fill its chamber. Long or undersized lines can also increase pressure losses and contribute to unstable delivery.

Depending on the application, installation accessories may include:

  • Safety valve: protects the pump and connected equipment from excessive discharge pressure. It should be placed in the discharge arrangement so that the pump cannot be isolated from its protection.
  • Pulsation dampers: reduce pulsation and can help limit related cavitation and overload concerns. Their position should be selected for the suction or discharge side as appropriate.
  • Pressure-sustaining valve: helps prevent excessive discharge when the pressure conditions are unsuitable for stable metering.
  • Foot valve or surge tank: may be appropriate where the suction arrangement could drain or where suction lift needs to be avoided.

Commission safely and adjust capacity carefully

Before start-up, confirm that the gear unit contains the specified oil; some pumps are supplied without oil. Check that the pump is protected against overload, that product is available, and that suction and discharge lines are open. Never start the pump with both line shutoff valves closed, and do not close them while it is running.

Set the stroke length to zero before starting. Where speed is variable, begin at the lowest speed. Start the motor, check its rotation, and increase speed and stroke length gradually. If possible, vent the piping with the pump operating without discharge pressure. Watch for leaks, then increase pressure gradually to the operating condition and set the required operating values.

A first estimate of stroke setting can be calculated in proportion to the required capacity:

Stroke length (%) = 100 × required capacity ÷ maximum capacity

This is an estimate, not a guarantee of delivered flow. Actual capacity can vary with operating pressure, liquid viscosity, suction and discharge piping, and installation arrangement. Where accuracy matters, determine actual delivery under the intended operating conditions by measuring the volume over a known number of strokes and recording the actual stroke frequency. Use that result to correct the setting. A flow-rate curve developed for those operating conditions is only applicable while those conditions remain comparable.

Build maintenance and troubleshooting into operations

Routine maintenance starts with checks that reveal changes before they become failures. Check gear-unit oil level regularly and follow the specified oil-change intervals for the pump. The motor and any accessories may have separate manufacturer instructions. Before working on the pump, isolate its power source, depressurize the pumphead and piping, and follow site procedures for handling process chemicals.

If delivery stops or becomes inconsistent, work through the system rather than assuming the pump mechanism is at fault. Common checks include:

  • Confirm power supply, motor operation and coupling condition.
  • Verify product availability and ensure suction and discharge valves are open.
  • Inspect filters and piping for blockage, and confirm pump valves are clean, undamaged and correctly oriented.
  • Check whether air or gas is trapped in the product chamber and vent the system as needed.
  • Review suction lift, discharge pressure and stroke setting against the operating requirements.
  • For low or unstable flow, inspect for leakage, damaged valve components, changing supply pressure or changing liquid viscosity.

Incorrect valve installation can cause pumphead damage. When servicing the diaphragm, use the specified assembly procedure and replace the complete double-diaphragm set if a diaphragm rupture has occurred. Process liquid may enter the pump yoke if both diaphragm layers fail, making thorough cleaning and inspection essential.

Practical implications for plant teams

Consistent metering relies on treating the pump, its controls and its connected piping as one system. Correct installation, pressure protection, careful venting and gradual start-up establish a sound operating baseline. Capacity calculations provide a useful starting point, but verification under actual process conditions is necessary when precise delivery is required. Regular oil and valve checks, combined with safe isolation and a methodical troubleshooting process, help teams maintain dependable operation and protect associated equipment.

Access Official Technical PDF

About The Author