Access Official Technical PDF

Share Summary:LinkedInEmail

A microstepping stepper motor system can offer more refined motion than a conventional stepper motor and separate drive, but its practical value depends on how the drive manages current, vibration and operating status. FASTECH’s Ezi-STEP MINI combines a motor with a DSP-equipped drive as an integrated system. Its functions include selectable microstep resolution, software damping, sensorless detection of lost synchronization and outputs for monitoring motion and faults.

For automation engineers and machine builders, these capabilities are relevant wherever positioning needs to be smooth and controlled across a range of speeds. The system is intended for applications including packaging, pick and place, vision systems, semiconductor equipment, laboratory testing and other automation tasks.

How the Ezi-STEP MINI microstepping stepper motor system works

The Ezi-STEP MINI uses a 32-bit digital signal processor and a bipolar PWM drive. The drive adjusts its PWM control signal every 25 microseconds to control motor current. This supports microstep operation, with selectable pulse-per-revolution settings ranging from 500 to 50,000. The default setting is 10,000 pulses per revolution.

The product literature also describes step-angle resolution from the motor’s basic 1.8 degrees down to 0.0072 degrees, or 1/250 of a full step. These settings give designers options for matching command resolution to an application’s motion requirements. Resolution should be considered alongside commanded speed: up to 10,000 pulses per revolution, the stated maximum speed is 3,000 rpm. At higher resolutions, the maximum speed is reduced accordingly.

Position and speed commands are supplied as a pulse train from a host controller. The drive accepts either 1-pulse or 2-pulse input modes, selected using a DIP switch. The maximum input frequency is 500 kHz at 50% duty cycle. Input circuitry is designed for 5 V TTL signals; the documentation specifies that a suitable series resistor is required for input signals above 5 V. Integrators should follow the wiring instructions for the signal voltage in use.

Software damping for smoother operation

Vibration can arise from changes in motor magnetic flux, reduced current associated with back EMF at higher speeds, and reduced phase voltage from the drive. Ezi-STEP MINI uses software damping and filtering algorithms to address these effects. The DSP adjusts the phase of the motor current according to rotor pole position, with the goal of suppressing vibration and enabling smoother operation at higher speeds.

This approach can be useful when motion smoothness matters across a broad speed range, rather than only at a single operating point. The drive’s features are intended to support high-speed operation while maintaining precise control. Actual suitability still depends on the motor model, load, resolution setting and application conditions; the published motor torque characteristics vary by motor size and speed.

Sensorless synchronization monitoring and drive signals

The integrated system includes an algorithm that estimates rotor position and detects when the motor is out of synchronization without relying on a separate position sensor for this function. The stated effectiveness of this detection applies above 300 rpm. This qualification matters when assessing whether sensorless loss-of-step monitoring is appropriate for a particular motion profile.

The drive provides alarm and run/stop outputs for a host controller. The run/stop output indicates that motor positioning is complete, while the alarm output changes state when a protection function is activated. Listed protection conditions include overcurrent, overspeed, step-out, overtemperature, excessive regenerative voltage, motor connection and motor voltage errors, as well as system and ROM errors. A motor-mounted drive LED indicates power, alarm and rotation direction; alarm flashing patterns identify different protection conditions.

When an alarm occurs, the drive signals the fault and disconnects power to the motor. The controller should monitor the alarm output and stop issuing motion commands when a protection condition is reported. An alarm reset input is also provided, but the source of the fault must be removed before resetting. This input is shared with the motor-free function, so its state must be managed carefully.

Integration, operating limits and brake considerations

The drive operates from a 24 VDC supply with a stated tolerance of ±10%. Its maximum current consumption is 500 mA, excluding motor current. The stated operating conditions include an ambient temperature of 0 to 50°C and humidity of 35 to 85% RH, non-condensing. The motor specifications list an operating temperature of 0 to 55°C, so system designers should check the relevant drive and motor limits when planning installation.

Pulse-train control, photocoupler-protected inputs and outputs, and separate motor and power connections support connection to a motion controller or PLC. The manufacturer lists signal and motor extension cables up to 20 m and a power cable up to 2 m. These limits should be taken into account when locating the drive and routing wiring.

Brake-equipped options are available for specified 42 mm motor models. The electronic brake is intended to hold position when power is off; it is not designed for braking a moving motor. The Ezi-STEP MINI itself does not control the brake. A host controller must manage brake power and timing, and the brake should not be operated while the motor is running. Incorrect sequencing can cause drive malfunction or allow a load to fall.

Conclusion: match drive settings to the motion task

The Ezi-STEP MINI brings microstepping, DSP-based current control, software damping and status monitoring together in a motor-and-drive system. Its selectable resolution and pulse inputs provide configuration choices for different motion-control requirements, while sensorless synchronization detection and protection outputs give the host controller information about operating status. Engineers should verify speed and resolution limits, wiring requirements, environmental conditions and controller responsibilities—including brake sequencing—before specifying the system. These checks help determine whether its integrated approach fits the machine’s motion and safety needs.

Access Official Technical PDF

About The Author