In nanoscale electronic devices, a semiconductor’s behavior is shaped not only by its material properties but also by the contacts that inject and collect current. Research on MoS2 interfacial transport shows that both the number of atomic layers and the material beneath them can influence current through a metal–semiconductor junction. For engineers and technical decision-makers, the findings underline a broader design consideration: contact interfaces can be a determining part of device behavior, not simply a connection to the active material.
Why the metal–MoS2 interface matters
Molybdenum disulfide (MoS2) is a layered transition-metal dichalcogenide being investigated for electronic and optoelectronic applications. A practical device requires metal contacts to deliver or collect charge. At the junction, an energy barrier can impede charge movement. Its height is associated with the alignment between the metal and the semiconductor’s energy bands, and it influences how readily current crosses the interface.
For few-layer materials, the barrier may change with thickness. Understanding that relationship is important when comparing devices or selecting a layer structure. Conventional techniques for measuring energy alignment can require relatively large samples, which are difficult to obtain when working with exfoliated flakes only a few layers thick. Local electrical probing offers another way to examine these small regions.
MoS2 interfacial transport depends on layer count
Conductive atomic force microscopy (CAFM) was used to measure current through vertical structures formed by a conductive probe, MoS2, and a conducting substrate. The MoS2 samples ranged from one to five layers and were placed on either template-stripped gold or indium tin oxide (ITO). The measurements showed that current generally increased as the layer count rose from one to five on both types of substrate.
The researchers analyzed forward-bias current using Fowler–Nordheim (FN) tunneling theory. In this model, an applied electric field narrows the barrier and enables charge carriers to tunnel through it. By analyzing the current–voltage response, the study estimated barrier heights for different layer counts. The estimated barrier height decreased as MoS2 thickness increased across the measured range.
Density functional theory (DFT) calculations for MoS2 on gold showed a corresponding trend. The calculations indicated that electron affinity increases with layer count, which was associated with a decreasing Schottky barrier. The experimental and computational results therefore both point to layer number as an important variable in vertical charge transport.
Substrate and surface quality influence measurements
The measured barrier height also depended on the conducting substrate. MoS2 on gold showed lower barrier heights than MoS2 on ITO, a difference the study attributed as likely related to the substrates’ different work functions. This means that results from a MoS2 junction cannot be interpreted from layer count alone: the contact materials and interface conditions also matter.
Surface flatness was central to the measurement approach. Because atomically thin MoS2 conforms to the surface beneath it, roughness can affect the local geometry and electrical contact. The study used ultra-flat template-stripped gold, with reported root-mean-square roughness of about 0.2 nm, and ITO with roughness below 0.7 nm. Measurements on rougher gold and commercially available ITO did not yield useful barrier-height information. The comparison reinforces the need to control substrate topography when using scanning-probe methods to characterize ultrathin materials.
The work also observed lower current near the edges of MoS2 layers than across the basal plane. The estimated width of the less-conducting edge region was approximately 20 nm, comparable to the probe-tip width. As a result, the measured edge feature could not be resolved as a smaller structure with the probe used. For local mapping, probe dimensions and spatial resolution therefore need to be considered when interpreting apparent interface or edge behavior.
Blue-light illumination produced negative photoconductivity
Photoconductive AFM measurements were made on MoS2 supported by transparent ITO. Under blue-light illumination in the 460–490 nm range, the measured current decreased rather than increased. This response is known as negative photoconductivity. It was also observed for few-layer MoS2 on a thinner, transparent gold substrate.
The reduction in current became more pronounced at higher applied bias, and the measured change was larger for layers two to five than for a monolayer. The authors proposed that illumination may change the interfacial barrier, increasing it and thereby reducing tunneling current. However, this explanation was not established as the definitive mechanism. The observed response was described as nontransient, distinguishing it from previously reported negative photoconductivity in planar MoS2 devices. Further investigation was identified as necessary to determine its origin.
Practical implications for device evaluation
These findings are relevant to teams assessing two-dimensional semiconductors for small-scale electronic and optoelectronic components. They show why comparisons between samples should account for several factors together:
- Layer count: Current and inferred barrier height changed with MoS2 thickness in the one-to-five-layer range.
- Contact material: Gold and ITO produced different barrier-height results.
- Substrate topography: Ultra-flat surfaces supported more useful local measurements than rougher substrates.
- Measurement conditions: Bias, illumination, probe characteristics and the location of the measurement affected the observed response.
The results do not establish a ready-made design rule for industrial equipment. Rather, they provide a materials-level view of how junction interfaces can shape electrical behavior, an important consideration as nanoscale devices are evaluated for future sensing, switching and optoelectronic applications.
Conclusion
In few-layer MoS2 vertical junctions, interfacial transport varied with both layer number and substrate. Current increased through five layers as the inferred barrier height declined, while gold and ITO produced different barrier characteristics. The study also identified less-conducting edges and a decrease in current under blue-light illumination. For device development and characterization, the practical message is to treat contact materials, surface quality, layer thickness and measurement conditions as connected design variables—and to distinguish observed effects from mechanisms that still require investigation.