Access Official Technical PDF

Share Summary:LinkedInEmail

Motion controllers coordinate motors, feedback devices and machine events to carry out tasks such as positioning, synchronized movement and coordinated multi-axis paths. Selecting motion controllers for an industrial automation project means looking beyond axis count: the control architecture, motion modes, feedback requirements, I/O and drive arrangement all affect how well the system fits the application.

A 2010–2011 Galil product catalog illustrates a broad approach to this selection process. Its portfolio spans high-performance and cost-oriented multi-axis controllers, single-axis units and a compact programmable controller for I/O. The specifications discussed here describe that catalog generation; confirm present-day product availability and documentation before using them in a new design.

Motion controllers: start with the application

Begin by defining what the machine must do. A basic axis may need jogging and point-to-point positioning, while a coordinated machine could require interpolation, electronic gearing or electronic camming. A controller’s supported motion modes determine whether control logic can be implemented directly or requires a different architecture.

The catalog’s Accelera series, including the DMC-40×0 Ethernet/RS232 and DMC-18×6 PCI families, supports a range of motion functions. These include point-to-point positioning, jogging, contouring, position-velocity-time (PVT) motion, linear and circular interpolation, electronic gearing and electronic camming. The DMC-40×0 family is listed in configurations from one to eight axes, with each axis configurable for stepper or servo operation.

For engineers, the practical question is how these capabilities map to machine sequences. Linear interpolation coordinates movement along a path; electronic gearing relates one axis to a master axis; and electronic camming uses a programmed relationship between axes. Choose features based on the motion profile and synchronization needs, rather than assuming every application needs the full command set.

Match performance to feedback and motion demands

Controller performance specifications matter when they correspond to real application requirements. The DMC-40×0 catalog lists encoder input frequencies up to 22 MHz and servo-loop update rates that vary by axis count and configuration. It also describes command processing as fast as 40 microseconds. These figures are not interchangeable: encoder rate concerns feedback input, servo-loop timing concerns control updates, and command-processing time describes another part of controller operation.

Review the complete control chain, including motor, amplifier, encoder and mechanical system. The catalog describes PID compensation with velocity and acceleration feedforward, integration limits, and notch and low-pass filters. Such functions provide tools for configuring control response, but the appropriate settings depend on the specific system and its tuning requirements.

Feedback compatibility is another selection point. The DMC-40×0 supports digital encoder inputs, with an optional module for interpolating sinusoidal encoder signals. The catalog also describes dual encoder inputs for servo axes. Confirm the selected controller and interface support the feedback devices and signal types required by the design.

Evaluate drive integration, I/O and communications

A motion controller can work with external drives or, in some configurations, include drives in the same package. The DMC-40×0 is described with optional internal servo or stepper drives, while external drives can also be connected. Integrated drives can affect cabinet layout, wiring and component selection; external drives may be appropriate when the application calls for a separate drive arrangement. Check motor compatibility, power requirements and the available interfaces against the actual system design.

I/O is equally important because motion often depends on machine signals. The DMC-40×0 catalog lists isolated home and travel-limit inputs for each axis, general-purpose digital inputs and outputs, analog inputs, high-speed position latching and position-compare outputs. These functions can support interactions between motion and external events, such as responding to an input or producing an output at a defined position. Verify both the I/O count and electrical characteristics, including isolation and output requirements.

Communications and installation format shape integration. The DMC-40×0 uses Ethernet and RS232, while the DMC-18×6 is a PCI-bus controller. The catalog also lists Econo Ethernet/RS232 and PCI families, single-axis controllers and the RIO Pocket PLC for programmable analog and digital I/O. This range reflects different needs: controller placement, host connection, axis count and whether the task is primarily motion control or I/O handling.

Consider programming and commissioning

Controller usability affects development and startup. The catalog describes an English-like, two-letter command set, on-board program storage, variables and arrays, and multitasking for up to eight programs on the Accelera family. It also describes GalilTools software for communication, tuning and viewing real-time data. These features can help engineers develop and troubleshoot applications, but project teams should assess the programming environment, host software and support materials that apply to the specific controller version.

When comparing options, use a structured checklist:

  • How many axes are needed now, and does the design require coordinated motion?
  • Which motion modes and synchronization functions are essential?
  • What motors, drives, encoders and feedback signals must be supported?
  • How many dedicated and general-purpose I/O points are required?
  • Does the installation call for Ethernet, serial communication or a bus-based controller?
  • Will drives be integrated with the controller or supplied separately?
  • What software, tuning and commissioning tools fit the team’s workflow?

Build the control architecture around the machine

The central lesson is to select a controller as part of the motion system, not as an isolated component. Axis count is only a starting point. Motion modes, feedback performance, drive integration, I/O and communications must all align with the machine’s operating sequence and installation constraints.

A careful comparison can also help avoid paying for unused capability or discovering a missing interface late in integration. Use product specifications to screen candidates, then confirm detailed requirements against current documentation and the complete motor, drive and feedback configuration. That process gives engineers and system integrators a clearer basis for designing a motion control system that is practical to implement and commission.

Access Official Technical PDF

About The Author