A nanosecond pulse generator must bring stored energy to a load quickly while providing a practical way to control when each pulse occurs. One architecture addresses this challenge by combining inductive and capacitive energy storage with two different switches: a controllable insulated-gate bipolar transistor (IGBT) and a fast closing switch, typically a spark gap. The division of roles allows the IGBT to manage the charging cycle while the closing switch produces the brief output pulse.
The design is intended for compact, low-power applications that need high-voltage pulses and a controllable operating cycle. Its demonstrated characteristics include a 2.57 ns average rise time, a stable repetition rate of up to 1,000 pulses per second, and a voltage gain of 50 under the reported test conditions. These results depend on the prototype configuration and should not be treated as universal specifications for every implementation.
Why combine inductive and capacitive storage?
A conventional high-voltage pulse generator typically includes a power supply, an energy-storage element, a switching system and a load. The storage element accumulates energy over a comparatively long interval; the switching system then redirects that energy to the load over a much shorter interval. Switch selection affects the pulse shape, timing and operating limits of the complete system.
Capacitive storage is commonly paired with closing switches, which connect the charged capacitor to the load. Inductive storage is more naturally associated with opening switches, which interrupt current and redirect energy. The hybrid design uses both: an inductor first stores energy from a low-voltage DC supply, then an IGBT opens the inductor circuit so that energy transfers into a capacitor. When the capacitor voltage reaches the spark gap’s breakdown level, the gap conducts and the capacitor discharges through the load.
This approach differs from a traditional Marx generator using spark gaps. The paper identifies challenges with that arrangement, including a system size that increases with the number of voltage-multiplying stages, repetition rate that is not directly controlled in the same way, and the need for a high-voltage supply. The hybrid design instead uses the IGBT as a controllable interface to the charging cycle.
Nanosecond pulse generator operation, phase by phase
1. Store energy in the inductor
The IGBT turns on and allows current to flow from the DC supply through the inductor. The current rises during the programmed activation interval, and energy accumulates in the inductor’s magnetic field. The IGBT’s on-time is therefore an important control input for the energy available in the subsequent stages.
2. Transfer energy to the capacitor
When the IGBT turns off, inductor current cannot stop instantaneously. It is redirected through the circuit and charges the capacitor. The inductor and capacitor form an LC network, and their interaction can raise the capacitor voltage above the input supply voltage. In practice, the attainable voltage and efficiency are affected by circuit resistance, magnetic-core behaviour and other losses.
3. Discharge through the load
Once the capacitor voltage exceeds the spark gap’s breakdown threshold, the gas between the electrodes ionizes and the gap conducts. The stored charge then flows through the load, producing the fast output pulse. The pulse’s leading edge depends on the switching process and parasitic inductance in the capacitor, wiring and load; it is not set by the IGBT’s switching speed alone.
4. Reset for the next cycle
After the capacitor discharges and the spark ends, the circuit waits for the next IGBT control signal. The theoretical repetition rate depends on the time required for the charging and discharge portions of the cycle. The spark gap’s recovery behaviour can impose an additional practical limit.
Control, efficiency and implementation considerations
The IGBT and spark gap serve different purposes rather than competing to perform the same switching task. The IGBT is fully controllable and can be driven from a control unit, but is not used to switch the fast, high-current capacitor discharge. The spark gap is fast and can handle high power, but in this design it fires automatically when its breakdown voltage is reached. That makes the IGBT useful for controlling the cycle, while the gap handles the rapid pulse-forming event.
The reported prototype used a 12 kV/30 A IGBT, a 4 nF high-voltage capacitor, a 1 mH inductor and a spark gap, powered by two 12 V batteries in series. With a 100 Ω load and 100 µs IGBT activation time, the reported output pulse was 1.2 kV, with a 2.57 ns average rise time and a 1 µs pulse width. The generator reached a stable repetition rate of 1,000 pulses per second in testing.
Designers should also account for timing uncertainty. Because the spark gap is not externally triggered, the delay from the IGBT signal to breakdown varies. In the reported test, delays ranged from 3.16 to 3.85 µs, with a standard deviation of 100 ns. This makes the spark-gap version less suitable where precise synchronization to an external event is essential.
Other practical factors include matching the generator to the load, managing inductor losses and magnetic-core saturation, and selecting capacitance and inductance to suit the required pulse width and charging interval. Additional components such as power-conditioning stages, pulse-forming networks or impedance-matching elements may be needed for a particular application.
Spark gap or avalanche BJT?
An avalanche-mode bipolar junction transistor (BJT) provides an alternative closing switch. In the reported comparison, a series-connected BJT arrangement produced a pulse rise time of about 1 ns and lower jitter than the spark-gap version. However, its voltage capability is limited by the transistors used, raising the voltage requires series connections, and the semiconductor option costs more.
The BJT also has a pulse-width limitation in the tested configuration. At higher load resistance, it could not remain in the desired secondary breakdown mode, leading to a change in operating behaviour and additional power dissipation. The spark gap, by contrast, is a low-cost option with broad power capability, but its timing is less precise and its repetition rate is constrained by gap dynamics. The appropriate choice depends on the required voltage, load, pulse width, timing precision and cost.
Practical implications
This hybrid nanosecond pulse generator illustrates how assigning distinct tasks to controllable and fast switches can produce a compact pulsed-power architecture. The IGBT provides control over inductive energy storage and capacitor charging; the spark gap or avalanche BJT performs the rapid discharge. For applications that can tolerate spark-gap timing variation, the low-cost configuration offers a simple route to short, high-voltage pulses. Where lower jitter and faster switching take priority, an avalanche BJT may be preferable, provided its voltage, current and pulse-width limits fit the application.