Nine-phase inverter THD reduction is a relevant design consideration when specifying multiphase drives for high-torque industrial applications. Inverter switching and nonlinear motor loads can produce harmonic components in voltage and current. These distortions can increase RMS current and contribute to heating in the load. A MATLAB/Simulink study compared conventional pulse width modulation (PWM) with third-harmonic injection PWM (THIPWM) for a nine-phase induction motor drive, reporting lower simulated THD with the injection method.
Why consider a nine-phase motor drive?
Three-phase drives are widely used, but applications with demanding torque requirements may benefit from a multiphase arrangement. The source study identifies ship propulsion, electric aircraft, hybrid electric vehicles, electric traction and battery-powered vehicles as potential applications for multiphase drives. It also notes potential advantages such as higher torque density, reduced torque pulsations, smoother torque, fault tolerance and lower inverter-leg ratings.
A nine-phase motor uses nine stator windings with phase relationships separated by 40 degrees. Its inverter must generate the corresponding set of phase outputs. In the modeled arrangement, a fixed DC supply feeds a nine-leg inverter with 18 switching devices. The study describes IGBTs as the switching devices and uses PWM control signals to operate the inverter legs.
These features make the drive more complex than a standard three-phase arrangement. Engineers must consider not only the motor and inverter topology but also the quality of the output waveforms and the effect of switching strategy on harmonics.
How PWM controls inverter output
Pulse width modulation controls the inverter switches by varying the widths of output pulses. In carrier-based PWM, a reference or modulating waveform is compared with a high-frequency triangular carrier. The reference establishes the desired fundamental output frequency, while the carrier determines switching frequency. The modulation index is based on the relationship between the reference and carrier amplitudes.
Conventional sinusoidal PWM uses sinusoidal reference signals. For a nine-phase drive, the inverter requires nine phase references, each offset from the next by 40 degrees. Comparing these references with the carrier produces switching pulses for the inverter legs. The resulting motor voltage and current are not perfectly sinusoidal; harmonic components accompany the fundamental frequency.
Total harmonic distortion (THD) expresses the combined contribution of harmonic components relative to the fundamental. In motor-drive applications, distortion matters because it can raise RMS current and contribute to additional heating. Harmonics can also affect power factor and electrical losses, making waveform quality an important part of drive design.
Nine-phase inverter THD reduction with THIPWM
Third-harmonic injection PWM modifies the sinusoidal reference by adding a third-harmonic component before it is compared with the triangular carrier. The injected component shapes, or flattens, the reference waveform near its peaks. This allows the fundamental reference component to be increased without immediately causing overmodulation, according to the study’s description.
The control concept still uses carrier comparison: the modified reference sets the desired fundamental output, and the triangular carrier governs switching. For the nine-phase implementation, the study generated nine phase-shifted control signals and applied positive and negative PWM pulses to the inverter switches.
Triplen-harmonic behavior depends on the phase relationships and the voltage being evaluated, so engineers should assess the actual phase and line quantities for their topology. In this work, the comparison was made through simulated inverter voltage and current waveforms and their FFT-based THD results.
What the simulation reported
The MATLAB/Simulink model was evaluated at a 50 Hz fundamental frequency with a 230 V DC supply. The reported parameters also included a 100 Hz triangular carrier, a 50 Hz modulating frequency, a modulation index of 1 and a 150 Hz third-harmonic component. The study compared conventional PWM and THIPWM using voltage and current harmonic analysis.
- Conventional PWM: 48.06% voltage THD and 13.46% current THD.
- THIPWM: 35.24% voltage THD and 9.83% current THD.
Under those modeled conditions, both voltage and current THD were lower with THIPWM than with conventional PWM. These figures describe the simulation setup and should not be treated as universal performance values for every nine-phase drive. Results in a practical system depend on the inverter, motor, switching and control parameters, and operating conditions.
Practical considerations for drive design
The comparison offers a useful starting point for evaluating modulation strategies, rather than a substitute for application-specific validation. Engineers and system integrators considering THIPWM should examine the effects of their chosen parameters on the relevant phase and line voltages, motor current and harmonic spectrum. Modeling can help compare strategies before commissioning, while measurements on the complete drive are needed to confirm behavior in the intended installation.
It is also important to distinguish a reduction in modeled THD from a complete assessment of motor thermal performance. The study identifies reduced harmonic-related heating as a motivation, but its reported comparison focuses on simulated waveforms and THD; temperature analysis is identified as a possible extension.
Conclusion
For the modeled nine-phase induction motor drive, third-harmonic injection PWM produced lower voltage and current THD than conventional PWM. The result highlights modulation strategy as one design lever for managing inverter waveform distortion in multiphase motor systems. For industrial applications, the practical takeaway is to evaluate THIPWM against conventional PWM using the actual drive topology, operating parameters and measured performance requirements—not to assume a single simulation result will apply universally.