Access Official Technical PDF

Share Summary:LinkedInEmail

As data rates rise, electrical links face channel limitations that can make high-speed communication more complex. Optical interconnects offer another way to move data between chips and systems, using light to carry signals through fiber, waveguides, or free space. For automation and computing hardware designers evaluating high-speed I/O, the benefits depend on more than the optical channel alone: transmitter and receiver choices, integration, and operating conditions all matter.

Why consider optical interconnects?

Short-distance optical links can have much lower channel loss and lower crosstalk than electrical connections. Optical waveguides can also be smaller than electrical traces, helping increase connection density. These characteristics can reduce some of the channel limitations that drive complexity in electrical links, including the need to manage signal degradation across the interconnect.

Optical links also offer the potential to carry multiple data channels on a single fiber through wavelength-division multiplexing (WDM). In WDM, signals at different wavelengths share an optical channel. This approach can increase information density without requiring a separate fiber for every data stream.

Choosing an optical channel

Short-distance optical I/O commonly uses fiber-based waveguides or free-space paths. Fiber is notable for low loss over distance: single-mode fiber loss is approximately 0.25 dB/km at 1550 nm, compared with roughly 100 dB/km for RF coaxial cable at 10 GHz. Optical fiber also has very low frequency-dependent loss over a broad bandwidth. However, dispersion can spread pulses and limit bandwidth, and laser linewidth becomes important for longer links, particularly beyond 1 km.

At the chip or package level, waveguide geometry affects how much interconnect density is possible. Examples include ribbon fiber and polymer waveguides built into a printed circuit board. The design trade-off is not simply optical versus electrical: packaging, alignment, the required number of channels, and the distance between endpoints influence which channel approach is practical.

Free-space systems are another proposed option. These use optical imaging to route light from one chip to another through air or glass. As with other approaches, the channel must be considered alongside how optical components are packaged and connected to the electronic system.

Optical interconnects: transmitter choices

An optical transmitter converts electrical data into changes in light. One option is to modulate a laser directly, varying its output power with the data. This is a simple approach, but it can introduce laser chirp: unwanted changes in the output wavelength. In long fibers, chirp can contribute to pulse dispersion.

Alternatively, a continuous-wave laser can provide steady optical power that an external modulator encodes with data. External modulation adds a component, but avoids the chirp associated with direct modulation and can produce a transform-limited spectrum. The difference matters especially when link distance makes dispersion a concern.

Common transmitter devices

  • Vertical-cavity surface-emitting lasers (VCSELs): Emit light from the top or bottom surface. They need to operate above threshold current to avoid turn-on delay, which can cause intersymbol interference. Higher bandwidth and reliability also involve a trade-off related to current density.
  • Electro-absorption modulators (EAMs): Use voltage-dependent absorption to modulate light. Their small size allows them to be treated as lumped-capacitance loads.
  • Ring-resonator modulators (RRMs): Change how light couples into a resonator. Their small size and ability to work with selected wavelengths make them useful in WDM designs.
  • Mach-Zehnder modulators (MZMs): Split light into two paths, change the phase in each, then recombine the paths. They are longer devices and may require drivers that handle a low-impedance transmission line and higher voltage swing, but are less sensitive to temperature variations than ring resonators.

Driver design must match the device. Current-mode drivers are often used with VCSELs, while voltage-mode CMOS drivers can drive small EAMs and RRMs. Some modulators may require a voltage swing above the nominal CMOS supply.

Receivers turn light back into electrical signals

At the receiving end, a photodetector converts optical power into current. Electrical amplifiers then produce a usable voltage signal. Receiver options include p-i-n photodiodes and integrated metal-semiconductor-metal detectors. In a p-i-n photodiode, light is absorbed in the intrinsic region to generate charge carriers; detector capacitance and carrier transit time are key considerations.

Integration can change the electrical load presented by the detector. For example, a waveguide-coupled germanium metal-semiconductor-metal detector described in the material has an active area below 2 μm² and capacitance below 1 fF. These figures illustrate one device design, not a general specification for optical receivers.

Integration shapes system trade-offs

Optical devices can be fabricated separately and connected to electronic chips through hybrid integration, such as wire bonding or flip-chip bonding. Alternatively, optical devices can be integrated with CMOS technology. Silicon-on-insulator (SOI) processes can provide a thicker buried oxide layer that confines light and enables low-loss waveguides. In bulk CMOS, a thin shallow-trench-isolation layer can allow light to leak into the silicon substrate, resulting in high loss unless additional processing is used.

Another integration approach fabricates waveguides and optical devices above the metal layers. This can reduce use of active chip area and allows the transistor and optical device processes to be optimized independently. Each approach brings different manufacturing and packaging considerations; the choice depends on the intended system architecture and integration requirements.

Conclusion

Optical interconnects can address important electrical-channel constraints through lower loss, reduced crosstalk, compact waveguides, and the potential for WDM. Realizing those advantages requires coordinated choices across the link: channel type, modulation method, detector and amplifier design, and optical integration. Engineers assessing high-speed I/O should evaluate the complete path rather than treating the optical medium as a standalone solution.

Access Official Technical PDF

About The Author