Access Official Technical PDF

Share Summary:LinkedInEmail

An optoNCDT 2300 laser sensor uses optical triangulation to provide non-contact measurements for industrial and laboratory applications. Depending on the sensor version and arrangement, it can measure displacement, distance, position or elongation, and certain configurations can measure the thickness of transparent objects. For automation engineers and system integrators, successful deployment depends on more than choosing a measuring range: target characteristics, mounting, signal handling, communications and laser safety all need to be considered.

How the optoNCDT 2300 uses optical triangulation

The sensor projects a modulated point of visible light onto a target. The reflected light is evaluated to determine the target’s position relative to the sensor. This optical triangulation principle allows measurement without mechanical contact with the object, making the system relevant to in-process quality control and dimensional testing.

In a diffuse arrangement, the sensor measures distance to a target surface. A direct arrangement is used for distance measurement or for measuring the thickness of a transparent object. These arrangements are not interchangeable: the intended measurement task and the target’s optical properties should guide sensor selection and installation.

The product family includes different models and variants, with the measurement options depending on the individual version. Confirm that the selected model supports the required task and measuring range using its applicable technical data before finalizing a machine design.

Choosing a measurement approach for automation

Start with the value the control system needs. A displacement or distance measurement may support position monitoring or dimensional checks, while thickness measurement requires the appropriate direct arrangement and a compatible sensor version. Define where the measurement will occur in the process, how the target will be presented, and how the result will be used by the control or quality system.

The sensor provides configuration options for measurement control and data handling, including triggering, synchronization, averaging, spike correction and statistical values. These settings should be selected to suit the application rather than treated as generic defaults. For example, an application that needs values in response to a trigger has different timing requirements from one that processes a continuous stream of measurements.

Output can be configured through digital interfaces, with Ethernet, RS422 and EtherCAT covered in the device documentation. The available output values and data formats depend on the interface and configuration. Integrators should plan the communications path, data selection and output timing alongside the PLC or measurement-server design, then verify that the receiving system interprets the transmitted values as intended.

Installation and target conditions

Mechanical stability and the optical path matter to measurement quality. Mount the sensor using its designated mounting holes on a flat surface; avoid shock and vibration. Protect the cable from damage, and do not exceed the specified supply-voltage limits. The operating instructions also caution against continuous exposure to fluids and aggressive materials.

Target and environmental conditions can influence results. The manual identifies reflection factor, light from other sources, color differences, surface roughness, temperature, mechanical vibration, movement blur and angle as factors to consider. A practical commissioning process should therefore assess the actual target surface and its motion in the installed geometry, rather than relying only on a nominal sensor-to-target distance.

Keep the optical surfaces clean. The stated IP65 protection applies only when the sensor cable is plugged in, and the lenses are excluded from that protection rating. Contamination of the lenses can impair operation. The specified operating temperature is 0 to 50 °C, with storage from -20 to 70 °C; the specified humidity range is 5 to 95 percent without condensation.

Configuration, diagnostics and commissioning

Sensor parameters can be managed through the Ethernet interface and web browser, or through ASCII commands. The documentation also describes measurement presentation and video-signal access through a browser. For EtherCAT installations, the manual covers configuration, process-data mapping, synchronization and troubleshooting. These options support different integration approaches, but the right choice depends on the machine network and control architecture.

During commissioning, verify the measurement behavior with the intended target and operating conditions. Check that the sensor is configured for the required measurement program, measuring rate, interface and output data. Where the application uses triggering or synchronization, confirm the relationship between the control signal and the values received by the automation system. Review error handling as part of the same test so that invalid or unavailable measurements are managed appropriately.

Laser safety is part of system design

The optoNCDT 2300 family includes laser classifications that vary by model. The operating instructions identify Class 2 and Class 3R versions, so safety procedures must follow the classification of the specific sensor being installed. Avoid direct exposure to the beam and observe applicable national laser-protection requirements. For Class 3R versions, the manual calls for a laser protection officer and a recognizable, restricted and marked laser area. If labels are obscured by installation, supplementary labels must be applied as required.

Switch off the sensor for cleaning, maintenance and system repair. The sensor housing is not intended to be opened by the user; service and repair are to be handled by the manufacturer. These precautions help make the measurement system safer to maintain and reduce the risk of damage.

Practical implications for integrators

The optoNCDT 2300 is best treated as a configurable measurement component within a larger automation system. Its triangulation principle establishes how it senses a target, but the application determines the suitable model, optical arrangement, settings and data path. A disciplined integration process should:

  • Match the sensor version and arrangement to the measurement task.
  • Assess target reflectivity, surface condition, angle and movement.
  • Provide stable mounting and protect the sensor, cable and optical surfaces.
  • Configure measurement processing, triggering and output for the control-system requirements.
  • Apply laser-safety measures based on the classification of the selected model.

Considering these factors together gives engineering teams a clearer basis for evaluating an optical triangulation sensor in dimensional inspection and in-process measurement. Careful selection, setup and validation are essential to integrating the optoNCDT 2300 into a reliable industrial measurement workflow.

Access Official Technical PDF

About The Author