In any document workflow, paper handling best practices help reduce misfeeds, protect output quality, and keep copying, printing, faxing, and scanning tasks moving. The fundamentals are straightforward: use media suited to the equipment, load it in the correct orientation, and make sure tray settings match the paper. Preparing originals carefully is just as important when documents need to be scanned or copied.
These principles apply to the SHARP MX-B350W and MX-B450W digital multifunction systems described here. The details below illustrate how operators can manage paper and originals on these machines while avoiding common causes of interruptions.
Match paper to the tray and the task
Not every media type can be loaded in every tray. On these models, the standard trays support several kinds of paper, including plain, recycled, colored, letterhead, pre-printed, and pre-punched stock. The bypass tray accepts additional media, including labels, glossy paper, transparencies, and envelopes. Heavy and thin papers also have tray-specific restrictions, so operators should confirm compatibility before loading.
Paper weight matters. The manual identifies plain paper in ranges from 60 to 105 g/m², heavy paper from 106 to 220 g/m², and thin paper from 55 to 59 g/m². The standard trays do not support every weight range; for example, heavy and thin paper are listed for tray 2, when installed, and the bypass tray rather than tray 1. Consult the machine’s specifications and the media manufacturer’s guidance when selecting stock.
Unsupported or unsuitable media can contribute to skewed feeding, misfeeds, poor toner adhesion, or machine problems. Examples of paper that should not be used include damp, curled, torn, creased, stapled, or irregularly shaped sheets, as well as paper that has already been printed on by another printer or multifunction device.
Load paper carefully and set tray options
Before loading a tray, pull it out gently and adjust its guides to the paper size. Fan the stack to separate sheets, then load it without exceeding the tray’s fill line. The paper should sit neatly against the guides, with no gap large enough to allow it to shift. Forcing a tray back into the machine can cause skewed feeding, so push it in slowly and firmly.
Orientation depends on the tray and media. For ordinary stock, trays 1 and 2 are loaded print side up, while the bypass tray is loaded print side down. Letterhead and pre-printed paper require the reverse orientation. Check the machine’s loading guidance for the specific tray and media before starting a job.
The bypass tray needs particular attention. Open its extension, load paper along the guides, and adjust them until they lightly contact the stack. Do not force sheets into the tray. For some plain paper and special media, the machine’s instructions call for feeding one sheet at a time. When adding paper to a partially used bypass tray, remove the remaining sheets, combine them with the new paper, and reload the stack together.
After loading, confirm both the paper size and type in the tray settings. A mismatch can interfere with automatic paper selection and result in printing on the wrong stock, a failed job, or a misfeed. Auto tray switching can allow a job to continue from another tray when the current tray runs out, provided the other tray contains paper of the same size and type. The feature does not apply to bypass-tray use or fax printing.
Take extra care with envelopes and special media
Envelopes should be loaded in the bypass tray in the specified orientation, with the front side facing down. Fold the flap and crease it sharply before loading. The machine does not support printing on both sides of an envelope, and some envelope constructions are unsuitable, including windowed, string-closed, damaged, or uneven envelopes.
Envelope printing can be sensitive to construction and operating conditions. The manual notes that creasing, smudging, misfeeds, or poor toner fusing may occur. If an envelope meets the machine’s specifications but still shows these issues, the fusing-unit pressure levers may need to be moved to the lower-pressure position as directed in the manual. Because the fusing unit is hot, this procedure requires care. Return the levers to the normal position before printing on other paper.
For transparencies, use the recommended film, fan sheets before loading multiple pieces, and remove each sheet from the output tray as it is produced. This helps avoid the curling that can occur when transparencies are left stacked together. Use only label sheets suitable for the machine, and follow any orientation instructions supplied with the labels.
Prepare originals for scanning and copying
Original handling can affect scan quality and feeding reliability. Use the automatic document feeder for suitable multi-page originals, aligning the edges and adjusting the guides to the document width. Remove staples and paper clips first, and allow correction fluid, ink, or paste to dry. Originals that are damaged, folded, crumpled, or loosely assembled may misfeed or produce smudges.
Some documents should be placed on the document glass instead. This includes books and other thick originals that cannot pass through the feeder, as well as transparent materials, tracing paper, carbon paper, thermal paper, and other types that the manual says not to feed through the automatic document feeder. Close the feeder slowly when using the glass.
For originals with two or three punched holes, position the punched edge away from the feeder’s feed slot and specify the document orientation as needed. Business cards may also require special attention because their material, shape, or construction can affect feeding and scanning.
Build consistent routines into daily operation
Reliable paper handling is largely a matter of repeatable checks. Before a job, operators can verify that:
- The paper type and weight are permitted in the selected tray.
- The stack is fanned, within the fill limit, and aligned with the guides.
- The print-side orientation is correct, especially for letterhead and pre-printed stock.
- The tray’s configured size and type match the loaded media.
- Special media and originals are prepared according to their handling requirements.
If a misfeed occurs, follow the machine’s instructions and take care around the fusing unit, which can be hot. Routine cleaning of the document glass, automatic document feeder, and paper-feed rollers is also part of maintaining dependable operation.
Conclusion
Good paper handling combines media selection, correct loading, accurate tray configuration, and appropriate original preparation. Applying these practices can help operators avoid preventable feed problems and support consistent document output. For any paper or media not explicitly covered by the machine’s specifications, verify suitability with the equipment dealer or service provider before putting it into regular use.