Access Official Technical PDF

Share Summary:LinkedInEmail

PCB manufacturing trends reflect a changing mix of market demand, material availability and process requirements. For fabricators and automation teams, the practical challenge is not simply adopting new equipment: it is coordinating production planning, materials procurement and process control as the industry evolves. A 2018 industry review and the outlook published in 2019 highlighted these pressures, including regional shifts in production, rising demand for 5G-related boards and new approaches to multilayer lamination.

PCB manufacturing trends: a shifting production landscape

The industry review reported that the 117 listed PCB manufacturers generated approximately $62 billion in sales in 2018, representing 83% of estimated global output. Their growth exceeded the reported global market growth rate for that year. The figures also illustrated how concentrated production was: the listed companies represented less than 5% of an estimated 2,400 manufacturers, yet accounted for most of the reported output.

Production was not distributed evenly across regions. Mainland China had the largest number of companies in the ranking and recorded the fastest growth among the regions summarized. The review also described an increase in investment in Southeast Asia, while PCB production in North America, Japan and Europe was under pressure. European investment, in particular, was described as focused on technological upgrades rather than simply expanding factory scale.

These figures require care when used for planning. The review noted that acquisition-related revenue could be consolidated under the purchasing company, while some manufacturers’ reported sales included assembly or subcontracting activity. It also contrasted estimates from two industry sources that differed significantly in their calculation of total market size. The reported direction of market change was similar, but the totals were not directly interchangeable.

Material availability and production planning

Demand for 5G infrastructure was expected to increase requirements for high-frequency, low-loss and multilayer PCBs. The 2019 outlook identified base stations, routers, servers and antennas among the applications contributing to demand. At the same time, the source described pressure on laminate supply: as manufacturers shifted capacity toward high-frequency materials, the availability and lead times of conventional FR-4 materials could be affected.

That situation reinforced a basic operational lesson: customized circuit boards and their materials require forward planning. The laminate market commentary described scheduled production and allocation practices as ways suppliers were managing demand. For PCB manufacturers, these practices can limit the ability to respond to orders at short notice. Forecast accuracy, early communication with PCB suppliers and timely material reservations therefore become part of production control, not just purchasing administration.

Manufacturers also had to consider geopolitical and supply-chain changes. The 2019 commentary discussed U.S.–China trade restrictions and their effects on companies’ sourcing strategies. It described moves to seek alternative supply sources and the possibility of production investment shifting toward Southeast Asia. These developments did not mean that China’s established PCB ecosystem would disappear quickly, but they added uncertainty to procurement and capacity decisions.

Rethinking multilayer PCB lamination

As board designs became more demanding, lamination remained a critical process for curing resin composites. Conventional presses typically generate heat using thermal oil, electrical heaters or steam, and transfer that heat through press platens to the material. The induction-based press concept described in the source takes a different approach: it uses electromagnetic energy to heat stainless-steel separator plates within the press stack.

In this arrangement, the separator plates transfer heat to the adjacent laminate panels. A temperature sensor embedded in a dummy panel provides feedback from within the stack, and a closed-loop control system uses that information to manage the programmed process. The intended benefit is more direct control of the temperature experienced by the material, rather than relying on heat to travel from large, externally heated platens through the stack.

How induction heating changes the process

The system’s coil produces a magnetic field that induces electrical currents in the stainless-steel plates. The resulting electrical energy is converted into heat in those plates. Because the design heats the separator plates rather than the full mass of the platens, the source describes lower thermal mass and reduced energy requirements for heating the press stack under its stated comparison. The actual result depends on the equipment and process conditions; the whitepaper’s comparison is an illustrative calculation, not a universal performance guarantee.

The concept also changes how temperature is monitored. A sensor located in a representative panel gives the control system a measurement of the material’s temperature, allowing the programmed profile to be adjusted using feedback. For process engineers, this emphasizes an important distinction: setting a temperature recipe is not the same as verifying the thermal conditions experienced inside the stack.

Automation still depends on human oversight

Automation can help standardize repeatable operations, but it does not remove the need for skilled supervision. The broader industry discussion stressed that human awareness and problem-solving remain central as manufacturing processes change. In lamination, operators and engineers still need to prepare the stack correctly, select appropriate recipes, interpret process feedback and respond when conditions depart from expectations.

This principle extends beyond the press. As factories introduce new materials and equipment, automation changes the work performed by people rather than eliminating it. Reliable production depends on combining machine control with staff who understand the process, its limits and the consequences of deviations.

Practical implications for PCB manufacturers

The trends described in the 2019 outlook point to several priorities for technical and operational teams:

  • Plan materials early. Forecast laminate needs and coordinate with suppliers when allocation or longer lead times may affect production.
  • Evaluate regional exposure. Consider how sourcing strategies and manufacturing locations could be affected by shifts in trade conditions and investment.
  • Validate process control. Assess whether temperature measurements represent conditions within the laminate stack, not only the press hardware.
  • Develop operator expertise. Ensure that staff can supervise automated processes and understand how recipe settings, feedback and material behavior interact.

PCB manufacturing trends are shaped by more than market growth: they influence material availability, factory investment and the control strategies needed to produce increasingly demanding boards. For manufacturers, the practical response is to connect procurement planning with process engineering, evaluate new lamination approaches against actual production needs, and keep knowledgeable people involved in automated operations. That combination can help teams adapt to change without losing sight of quality and process reliability.

Access Official Technical PDF

About The Author